参数资料
型号: LT1961IMS8E#TR
厂商: LINEAR TECHNOLOGY CORP
元件分类: 稳压器
英文描述: 3 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PDSO8
封装: PLASTIC, MSOP-8
文件页数: 12/16页
文件大小: 154K
代理商: LT1961IMS8E#TR
5
LT1961
1961fa
FB: The feedback pin is used to set output voltage using an
external voltage divider that generates 1.2V at the pin with
the desired output voltage. If required, the current limit
can be reduced during start up when the FB pin is below
0.5V (see the Current Limit Foldback graph in the Typical
Performance Characteristics section). An impedance of
less than 5k
Ω at the FB pin is needed for this feature to
operate.
VIN: This pin powers the internal circuitry and internal
regulator. Keep the external bypass capacitor close to this
pin.
GND: Short GND pins 3 and 4 and the exposed pad on the
PCB. The GND is the reference for the regulated output, so
load regulation will suffer if the “ground” end of the load
is not at the same voltage as the GND of the IC. This
condition occurs when the load current flows through the
metal path between the GND pins and the load ground
point. Keep the ground path short between the GND pins
and the load and use a ground plane when possible. Keep
the path between the input bypass and the GND pins short.
The exposed pad should be attached to a large copper area
to improve thermal resistance.
VSW: The switch pin is the collector of the on-chip power
NPN switch and has large currents flowing through it.
Keep the traces to the switching components as short as
possible to minimize radiation and voltage spikes.
SYNC: The sync pin is used to synchronize the internal
oscillator to an external signal. It is directly logic compat-
ible and can be driven with any signal between 20% and
80% duty cycle. The synchronizing range is equal to
initial
operating frequency, up to 2MHz. See Synchronization
section in Applications Information for details. When not
in use, this pin should be grounded.
SHDN: The shutdown pin is used to turn off the regulator
and to reduce input drain current to a few microamperes.
The 1.35V threshold can function as an accurate under-
voltage lockout (UVLO), preventing the regulator from
operating until the input voltage has reached a predeter-
mined level. Float or pull high to put the regulator in the
operating mode.
VC: The VC pin is the output of the error amplifier and the
input of the peak switch current comparator. It is normally
used for frequency compensation, but can do double duty
as a current clamp or control loop override. This pin sits
at about 0.3V for very light loads and 0.9V at maximum
load.
PIN FUNCTIONS
UU
U
相关PDF资料
PDF描述
LT3092ITS8#PBF SPECIALTY ANALOG CIRCUIT, PDSO8
LT3092ETS8#TRPBF SPECIALTY ANALOG CIRCUIT, PDSO8
LT3092EST#PBF SPECIALTY ANALOG CIRCUIT, PDSO3
LT3092ETS8 SPECIALTY ANALOG CIRCUIT, PDSO8
LT3092IST#PBF SPECIALTY ANALOG CIRCUIT, PDSO3
相关代理商/技术参数
参数描述
LT1961IMS8ETRPBF 制造商:LINER 制造商全称:Linear Technology 功能描述:1.5A, 1.25MHz Step-Up Switching Regulator
LT1962 制造商:LINER 制造商全称:Linear Technology 功能描述:Micropower Low Dropout Regulators with Shutdown
LT1962EMS8 功能描述:IC REG LDO ADJ .3A 8-MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 产品培训模块:More Information on LDOs 标准包装:50 系列:- 稳压器拓扑结构:正,固定式 输出电压:3.3V 输入电压:最高 15V 电压 - 压降(标准):1.1V @ 800mA 稳压器数量:1 电流 - 输出:800mA 电流 - 限制(最小):800mA 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-263-4,D²Pak(3 引线+接片),TO-263AA 供应商设备封装:D2PAK-3 包装:管件
LT1962EMS8#PBF 功能描述:IC REG LDO ADJ .3A 8-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 产品培训模块:MIC5365/66 Ultra-small LDO Regulators 标准包装:1 系列:- 稳压器拓扑结构:正,固定式 输出电压:3V 输入电压:最高 5.5V 电压 - 压降(标准):0.155V @ 150mA 稳压器数量:1 电流 - 输出:150mA 电流 - 限制(最小):200mA 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:4-UDFN 裸露焊盘,4-TMLF? 供应商设备封装:4-TMLF?(1x1) 包装:Digi-Reel® 其它名称:576-3192-6
LT1962EMS8#PBF 制造商:Linear Technology 功能描述:Linear Voltage Regulator IC 制造商:Linear Technology 功能描述:IC, ADJ LDO REG 1.22V TO 20V 0.3A MSOP-8