- 您现在的位置：买卖IC网 > PDF目录13079 > LT1963AEST-3.3#TRPBF (Linear Technology)IC REG LDO 3.3V 1.5A SOT-223 PDF资料下载
参数资料
| 型号： | LT1963AEST-3.3#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 15/28页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 3.3V 1.5A SOT-223 |
| 产品培训模块： | More Information on LDOs |
| 标准包装： | 1 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 3.3V |
| 输入电压： | 最高 20V |
| 电压 - 压降（标准）： | 0.34V @ 1.5A |
| 稳压器数量： | 1 |
| 电流 - 输出： | 1.5A |
| 电流 - 限制（最小）： | 1.6A |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | TO-261-4，TO-261AA |
| 供应商设备封装： | SOT-223 |
| 包装： | 标准包装 |
| 产品目录页面： | 1330 (CN2011-ZH PDF) |
| 其它名称： | LT1963AEST-3.3#TRPBFDKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LT1963A Series
APPLICATIONS INFORMATION
Table 1. Capacitor Minimum ESR
V OUT 10μF 22μF
1.2V 20mΩ 15mΩ
1.5V 20mΩ 15mΩ
1.8V 15mΩ 10mΩ
2.5V 5mΩ 5mΩ
47μF
10mΩ
10mΩ
10mΩ
5mΩ
100μF
5mΩ
5mΩ
5mΩ
5mΩ
POSCAP capacitors are used. The output voltage is at the
worst case value of 1.2V. Trace A, is with a 10μF ceramic
output capacitor and shows significant ringing with a peak
amplitude of 25mV. For Trace B, a 22μF/45mΩ POSCAP
is added in parallel with the 10μF ceramic. The output is
well damped and settles to within 10mV in less than 20μs.
3.3V 0mΩ 0mΩ 0mΩ 5mΩ
≥5V 0mΩ 0mΩ 0mΩ 0mΩ
Figures 3 through 8 show the effect of ESR on the transient
response of the regulator. These scope photos show the
transient response for the LT1963A at three different output
voltages with various capacitors and various values of ESR.
The output load conditions are the same for all traces. In
all cases there is a DC load of 500mA. The load steps up
to 1A at the first transition and steps back to 500mA at
the second transition.
At the worst case point of 1.2V OUT with 10μF C OUT
(Figure 3), a minimum amount of ESR is required. While
20mΩ is enough to eliminate most of the ringing, a value
closer to 50mΩ provides a more optimum response. At
2.5V output with 10μF C OUT (Figure 4) the output rings
at the transitions with 0Ω ESR but still settles to within
10mV in 20μs after the 0.5A load step. Once again a small
value of ESR will provide a more optimum response.
At 5V OUT with 10μF C OUT (Figure 5) the response is well
damped with 0Ω ESR.
With a C OUT of 100μF at 0Ω ESR and an output of 1.2V
(Figure 6), the output rings although the amplitude is
only 20mV p-p . With C OUT of 100μF it takes only 5mΩ to
20mΩ of ESR to provide good damping at 1.2V output.
Performance at 2.5V and 5V output with 100μF C OUT shows
similar characteristics to the 10μF case (see Figures 7-8).
At 2.5V OUT 5mΩ to 20mΩ can improve transient response.
At 5V OUT the response is well damped with 0Ω ESR.
Capacitor types with inherently higher ESR can be combined
with 0mΩ ESR ceramic capacitors to achieve both good
high frequency bypassing and fast settling time. Figure
9 illustrates the improvement in transient response that
can be seen when a parallel combination of ceramic and
For Trace C, a 100μF/35mΩ POSCAP is connected in parallel
with the 10μF ceramic capacitor. In this case the peak output
deviation is less than 20mV and the output settles in about
10μs. For improved transient response the value of the
bulk capacitor (tantalum or aluminum electrolytic) should
be greater than twice the value of the ceramic capacitor.
Tantalum and Polytantalum Capacitors
There is a variety of tantalum capacitor types available,
with a wide range of ESR specifications. Older types have
ESR specifications in the hundreds of mΩ to several Ohms.
Some newer types of polytantalum with multi-electrodes
have maximum ESR specifications as low as 5mΩ. In gen-
eral the lower the ESR specification, the larger the size and
the higher the price. Polytantalum capacitors have better
surge capability than older types and generally lower ESR.
Some types such as the Sanyo TPE and TPB series have
ESR specifications in the 20mΩ to 50mΩ range, which
provide near optimum transient response.
Aluminum Electrolytic Capacitors
Aluminum electrolytic capacitors can also be used with the
LT1963A. These capacitors can also be used in conjunction
with ceramic capacitors. These tend to be the cheapest
and lowest performance type of capacitors. Care must be
used in selecting these capacitors as some types can have
ESR which can easily exceed the 3Ω maximum value.
Ceramic Capacitors
Extra consideration must be given to the use of ceramic
capacitors. Ceramic capacitors are manufactured with a
variety of dielectrics, each with different behavior over
temperature and applied voltage. The most common
dielectrics used are Z5U, Y5V, X5R and X7R. The Z5U and
15
For more information www.linear.com/LT1963A
1963aff
相关PDF资料 |
PDF描述 |
|---|---|
| MIC29510-5.0WT | IC REG LDO 5A 5V TO220-3 |
| VE-J5K-EZ-B1 | CONVERTER MOD DC/DC 40V 25W |
| LTC3831EGN#TRPBF | IC SW REG CONTROLLR SYNC 16-SSOP |
| HBC31DRXH-S734 | CONN EDGECARD 62POS DIP .100 SLD |
| LTC1262IS8#TR | IC CONV DC/DC FLASH MEMORY 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1963AET | 功能描述:IC REG LDO ADJ 1.5A TO220-5 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:800 系列:- 稳压器拓扑结构:正，固定式 输出电压:2.5V 输入电压:最高 16V 电压 - 压降（标准）:0.7V @ 4A 稳压器数量:1 电流 - 输出:4A 电流 - 限制（最小）:4.2A 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-263-6，D²Pak（5 引线+接片），TO-263BA 供应商设备封装:TO-263-5 包装:带卷 (TR) 其它名称:AP1184K525L-13AP1184K525LDITR |
| LT1963AET#06PBF | 功能描述:IC REG LDO ADJ 1.5A TO220-5 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:8V 输入电压:10.5 V ~ 23 V 电压 - 压降（标准）:1.7V @ 40mA 稳压器数量:1 电流 - 输出:100mA（最小值） 电流 - 限制（最小）:- 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:剪切带 (CT) 产品目录页面:1075 (CN2011-ZH PDF) 其它名称:296-24390-1 |
| LT1963AET#PBF | 功能描述:IC REG LDO ADJ 1.5A TO220-5 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:8V 输入电压:10.5 V ~ 23 V 电压 - 压降（标准）:1.7V @ 40mA 稳压器数量:1 电流 - 输出:100mA（最小值） 电流 - 限制（最小）:- 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:剪切带 (CT) 产品目录页面:1075 (CN2011-ZH PDF) 其它名称:296-24390-1 |
| LT1963AET-1.5 | 功能描述:IC REG LDO 1.5V 1.5A TO220-5 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:800 系列:- 稳压器拓扑结构:正，固定式 输出电压:2.5V 输入电压:最高 16V 电压 - 压降（标准）:0.7V @ 4A 稳压器数量:1 电流 - 输出:4A 电流 - 限制（最小）:4.2A 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-263-6，D²Pak（5 引线+接片），TO-263BA 供应商设备封装:TO-263-5 包装:带卷 (TR) 其它名称:AP1184K525L-13AP1184K525LDITR |
| LT1963AET-1.5#06PBF | 功能描述:IC REG LDO 1.5V 1.5A TO-220-5 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:800 系列:- 稳压器拓扑结构:正，固定式 输出电压:2.5V 输入电压:最高 16V 电压 - 压降（标准）:0.7V @ 4A 稳压器数量:1 电流 - 输出:4A 电流 - 限制（最小）:4.2A 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-263-6，D²Pak（5 引线+接片），TO-263BA 供应商设备封装:TO-263-5 包装:带卷 (TR) 其它名称:AP1184K525L-13AP1184K525LDITR |
发布紧急采购，3分钟左右您将得到回复。