参数资料
| 型号： | LT1965EQ-1.5#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 14/22页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 1.5V 1.1A 5-DDPAK |
| 产品培训模块： | More Information on LDOs |
| 标准包装： | 50 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 1.5V |
| 输入电压： | 最高 20V |
| 电压 - 压降（标准）： | 0.31V @ 1.1A |
| 稳压器数量： | 1 |
| 电流 - 输出： | 1.1A |
| 电流 - 限制（最小）： | 1.2A |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | TO-263-6，D²Pak（5 引线+接片），TO-263BA |
| 供应商设备封装： | D2PAK-5 |
| 包装： | 管件 |
| 产品目录页面： | 1330 (CN2011-ZH PDF) |
LT1965 Series
APPLICATIONS INFORMATION
is rising, the input-to-output voltage differential is small,
allowing the regulator to supply large output currents.
With a high input voltage, a problem can occur wherein
removal of an output short will not allow the output to
recover. Other regulators, such as the LT1083/LT1084/
LT1085 family, also exhibit this phenomenon, so it is not
unique to the LT1965.
The problem occurs with a heavy output load when the
input voltage is high and the output voltage is low. Com-
mon situations occur immediately after the removal of a
short-circuit or if the shutdown pin is pulled high after the
input voltage has already been turned on. The load line for
such a load may intersect the output current curve at two
points. If this happens, there are two stable output operat-
ing points for the regulator. With this double intersection,
the input power supply may need to be cycled down to
zero and brought up again to make the output recover.
Output Voltage Noise
The LT1965 regulators are designed to provide low output
voltage noise over the 10Hz to 100kHz bandwidth while
operating at full load. Output voltage noise is approximately
80nV/√ Hz over this frequency bandwidth for the LT1965
adjustable version. For higher output voltages (generated
by using a resistor divider), the output voltage noise gains
up accordingly.
Higher values of output voltage noise may be measured
if care is not exercised with regard to circuit layout and
testing. Crosstalk from nearby traces can induce unwanted
noise onto the LT1965’s output. Power supply ripple rejec-
tion must also be considered; the LT1965 regulators do
not have unlimited power supply rejection and will pass
a small portion of the input noise through to the output.
Thermal Considerations
The LT1965’s maximum rated junction temperature of
125°C (LT1965E, LT1965I) or 150°C (LT1965H) limits
its power handling capability. Two components comprise
the power dissipated by the device:
1. Output current multiplied by the input/output voltage
differential: I OUT ? ( V IN – V OUT ), and
2. GND pin current multiplied by the input voltage:
I GND ? V IN
GND pin current is determined using the GND Pin Current
curves in the Typical Performance Characteristics section.
Power dissipation equals the sum of the two components
listed.
The LT1965 regulators have internal thermal limiting that
protect the device during overload conditions. For con-
tinuous normal conditions, do not exceed the maximum
junction temperature rating of 125°C (E-grade, I-grade) or
150°C (H-grade). Carefully consider all sources of thermal
resistance from junction to ambient including other heat
sources mounted in proximity to the LT1965.
The underside of the LT1965 DFN package has exposed
metal (4mm 2 ) from the lead frame to the die attachment.
The underside of the LT1965 MSOP package also has
exposed metal (3.7mm 2 ). Both packages allow heat to
directly transfer from the die junction to the printed circuit
board metal to control maximum operating junction tem-
perature. The dual-in-line pin arrangement allows metal
to extend beyond the ends of the package on the topside
(component side) of a PCB. Connect this metal to GND
on the PCB. The multiple IN and OUT pins of the LT1965
also assist in spreading heat to the PCB.
For surface mount devices, heat sinking is accomplished
by using the heat spreading capabilities of the PC board
and its copper traces. Copper board stiffeners and plated
through-holes can also be used to spread the heat gener-
ated by power devices.
14
For more information www.linear.com/LT1965
1965fb
相关PDF资料 |
PDF描述 |
|---|---|
| ACM18DSAH | CONN EDGECARD 36POS R/A .156 SLD |
| ABC40DREF | CONN EDGECARD 80POS .100 EYELET |
| ACM28DRTF | CONN EDGECARD 56POS DIP .156 SLD |
| LT1965IMS8E#TRPBF | IC REG LDO ADJ 1.1A 8-MSOP |
| ABM28DRTF | CONN EDGECARD 56POS DIP .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1965EQ-2.5#PBF | 功能描述:IC REG LDO 2.5V 1.1A 5-DDPAK RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:800 系列:- 稳压器拓扑结构:正，固定式 输出电压:2.5V 输入电压:最高 16V 电压 - 压降（标准）:0.7V @ 4A 稳压器数量:1 电流 - 输出:4A 电流 - 限制（最小）:4.2A 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-263-6，D²Pak（5 引线+接片），TO-263BA 供应商设备封装:TO-263-5 包装:带卷 (TR) 其它名称:AP1184K525L-13AP1184K525LDITR |
| LT1965EQ-2.5#TRPBF | 功能描述:IC REG LDO 2.5V 1.1A 5-DDPAK RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:800 系列:- 稳压器拓扑结构:正，固定式 输出电压:2.5V 输入电压:最高 16V 电压 - 压降（标准）:0.7V @ 4A 稳压器数量:1 电流 - 输出:4A 电流 - 限制（最小）:4.2A 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-263-6，D²Pak（5 引线+接片），TO-263BA 供应商设备封装:TO-263-5 包装:带卷 (TR) 其它名称:AP1184K525L-13AP1184K525LDITR |
| LT1965EQ-3.3#PBF | 功能描述:IC REG LDO 3.3V 1.1A 5-DDPAK RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:8V 输入电压:10.5 V ~ 23 V 电压 - 压降（标准）:1.7V @ 40mA 稳压器数量:1 电流 - 输出:100mA（最小值） 电流 - 限制（最小）:- 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:剪切带 (CT) 产品目录页面:1075 (CN2011-ZH PDF) 其它名称:296-24390-1 |
| LT1965EQ-3.3#PBF | 制造商:Linear Technology 功能描述:LDO FIXED 3.3V 1.1A TO-263 制造商:Linear Technology 功能描述:LDO, FIXED, 3.3V, 1.1A, TO-263-5 |
| LT1965EQ-3.3#TRPBF | 功能描述:IC REG LDO 3.3V 1.1A 5-DDPAK RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:800 系列:- 稳压器拓扑结构:正，固定式 输出电压:2.5V 输入电压:最高 16V 电压 - 压降（标准）:0.7V @ 4A 稳压器数量:1 电流 - 输出:4A 电流 - 限制（最小）:4.2A 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-263-6，D²Pak（5 引线+接片），TO-263BA 供应商设备封装:TO-263-5 包装:带卷 (TR) 其它名称:AP1184K525L-13AP1184K525LDITR |
发布紧急采购，3分钟左右您将得到回复。