参数资料
| 型号： | LT1969CMS |
| 厂商： | Linear Technology |
| 文件页数： | 8/20页 |
| 文件大小： | 0K |
| 描述： | IC OP-AMP ADJ CURRNT DUAL 10MSOP |
| 标准包装： | 50 |
| 放大器类型： | 通用 |
| 电路数： | 2 |
| 转换速率： | 200 V/µs |
| 增益带宽积： | 700MHz |
| 电流 - 输入偏压： | 1.5µA |
| 电压 - 输入偏移： | 1000µV |
| 电流 - 电源： | 7mA |
| 电流 - 输出 / 通道： | 700mA |
| 电压 - 电源，单路/双路(±)： | 4 V ~ 13 V，±2 V ~ 6.5 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 10-MSOP |
| 包装： | 管件 |
16
LT1969
Figure 10. Receiver Configuration
RBT
–Va
Va
–VL
VL
RBT
1969 F10
1:n
RL
+
–
VBIAS
VRX
+
–
LT1813
+
–
LT1813
RF
RG
RD
RG
RD
RL
n2
= REFLECTED IMPEDANCE
RL
2n2
RL
2n2
= ATTENUATION OF Va
+ RBT
RL
2n2
RL
2n2
RG
RD
=
SET
+ RBT
is also 10, but the power consumption has been reduced
to 350mW, a savings of 36% over the previous design.
Note that the reduction of the back-termination resistor
has allowed use of a 1:1 transformer ratio.
Table 2 compares the two approaches. It may seem that
the low power design is a clear choice, but there are further
system issues to consider. In addition to driving the line,
the amplifiers provide back-termination for signals that
are received simultaneously from the line. In order to
reject the drive signal, a receiver circuit is used such as
shown in Figure 10. Taking advantage of the differential
nature of the signals, the receiver can subtract out the
drive signal and amplify the received signal. This method
works well for standard back-termination. If the back-
termination resistors are reduced by positive feedback, a
portion of the received signal also appears at the amplifier
outputs. The result is that the received signal is attenuated
by the same amount as the reduction in the back-termina-
tion resistor. Taking into account the different transformer
turns ratios, the received signal of the low power design
will be one third of the standard design received signal.
The reduced signal has system implications for the sensi-
tivity of the receiver. The power reduction may, or may not,
be an acceptable system tradeoff for a given design.
Controlling the Quiescent Current
The quiescent current of the LT1969 is controlled via two
control pins, CTRL1 and CTRL2. The pins can be used to
either turn off the amplifiers, reducing the quiescent cur-
rent on
±2.5V supplies to less than 500A per amplifier, or
to control the quiescent current in normal operation.
Figure 11 shows how the control pins are used in conjunc-
tion with external resistors to program the supply current.
In normal operation, each control pin is biased to approxi-
mately 1V above V – and by varying the resistor values, the
current from each control pin can be adjusted. It is this
current that sets the supply current of both amplifiers. If
one of the resistors is open, i.e. R2, the supply current of
the amplifiers will be set by CTRL1 and R1. Figure 12
shows supply current vs resistor value.
APPLICATIO S I FOR ATIO
WU
UU
相关PDF资料 |
PDF描述 |
|---|---|
| SSQ-109-02-S-S | CONN RCPT .100" 9POS SNGL GOLD |
| LT1217CN8#PBF | IC CURRNT FEEDBCK AMP 10MHZ 8DIP |
| LT1217CN8 | IC CURRNT FEEDBCK AMP 10MHZ 8DIP |
| LT1920CS8#PBF | IC PREC INSTRUMNTATION AMP 8SOIC |
| LT1920CS8 | IC PREC INSTRUMNTATION AMP 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1969CMS#PBF | 功能描述:IC OP-AMP ADJ CURRNT DUAL 10MSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:2,500 系列:- 放大器类型:通用 电路数:2 输出类型:满摆幅 转换速率:350 V/µs 增益带宽积:180MHz -3db带宽:320MHz 电流 - 输入偏压:12.5µA 电压 - 输入偏移:800µV 电流 - 电源:15mA 电流 - 输出 / 通道:85mA 电压 - 电源，单路/双路(±):2.5 V ~ 12.6 V，±1.25 V ~ 6.3 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MSOP 包装:带卷 (TR) |
| LT1969CMS#TR | 功能描述:IC OP-AMP ADJ CURRNT DUAL 10MSOP RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1 系列:- 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.028 V/µs 增益带宽积:105kHz -3db带宽:- 电流 - 输入偏压:3nA 电压 - 输入偏移:100µV 电流 - 电源:3.3µA 电流 - 输出 / 通道:12mA 电压 - 电源，单路/双路(±):2.7 V ~ 12 V，±1.35 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:剪切带 (CT) 其它名称:OP481GRUZ-REELCT |
| LT1969CMS#TRPBF | 功能描述:IC OP-AMP ADJ CURRNT DUAL 10MSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1 系列:- 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.028 V/µs 增益带宽积:105kHz -3db带宽:- 电流 - 输入偏压:3nA 电压 - 输入偏移:100µV 电流 - 电源:3.3µA 电流 - 输出 / 通道:12mA 电压 - 电源，单路/双路(±):2.7 V ~ 12 V，±1.35 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:剪切带 (CT) 其它名称:OP481GRUZ-REELCT |
| LT1970 | 制造商:LINER 制造商全称:Linear Technology 功能描述:500mA Power Op Amp with Adjustable Precision Current Limit |
| LT1970_1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:500mA Power Op Amp with Adjustable Precision Current Limit |
发布紧急采购，3分钟左右您将得到回复。