参数资料
| 型号： | LT1993CUD-4#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 3/16页 |
| 文件大小： | 0K |
| 描述： | IC DIFF AMP/ADC DRVR 16-QFN |
| 标准包装： | 2,500 |
| 放大器类型： | 差分 |
| 电路数： | 2 |
| 输出类型： | 差分 |
| 转换速率： | 1100 V/µs |
| -3db带宽： | 900MHz |
| 电流 - 输入偏压： | 5µA |
| 电压 - 输入偏移： | 1000µV |
| 电流 - 电源： | 100mA |
| 电流 - 输出 / 通道： | 45mA |
| 电压 - 电源，单路/双路(±)： | 4 V ~ 5.5 V，±2 V ~ 2.5 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-WFQFN 裸露焊盘 |
| 供应商设备封装： | 16-QFN-EP（3x3） |
| 包装： | 带卷 (TR) |
LT1993-4
11
19934fa
APPLICATIO S I FOR ATIO
WU
U
Circuit Description
The LT1993-4 is a low noise, low distortion differential
amplier/ADC driver with:
DC to 900MHz –3dB bandwidth
Fixed gain of 4V/V (12dB) independent of RLOAD
100
Ω differential input impedance
Low output impedance
Built-in, user adjustable output ltering
Requires minimal support circuitry
Referring to the block diagram, the LT1993-4 uses a closed-
loop topology which incorporates 3 internal ampliers.
Two of the ampliers (A and B) are identical and drive the
differential outputs. The third amplier (C) is used to set
the output common mode voltage. Gain and input imped-
ance are set by the 100
Ω/200Ω resistors in the internal
feedback network. Output impedance is low, determined
by the inherent output impedance of ampliers A and B,
and further reduced by internal feedback.
The LT1993-4 also includes built-in single-pole output
ltering. The user has the choice of using the unltered
outputs, the ltered outputs (175MHz –3dB lowpass), or
modifying the ltered outputs to alter frequency response
by adding additional components. Many lowpass and
bandpass lters are easily implemented with just one or
two additional components.
The LT1993-4 has been designed to minimize the need
for external support components such as transformers or
AC-coupling capacitors. As an ADC driver, the LT1993-4
requires no external components except for power-supply
bypass capacitors. This allows DC-coupled operation for
applications that have frequency ranges including DC.
At the outputs, the common mode voltage is set via the
VOCM pin, allowing the LT1993-4 to drive ADCs directly. No
output AC-coupling capacitors or transformers are needed.
At the inputs, signals can be differential or single-ended
with virtually no difference in performance. Furthermore,
DC levels at the inputs can be set independently of the
output common mode voltage. These input characteristics
often eliminate the need for an input transformer and/or
AC-coupling capacitors.
Input Impedance and Matching Networks
Because of the internal feedback network, calculation of
the LT1993-4’s input impedance is not straightforward
from examination of the block diagram. Furthermore, the
input impedance when driven differentially is different than
when driven single-ended. When driven differentially, the
LT1993-4’s input impedance is 100
Ω (differential); when
driven single-ended, the input impedance is 75
Ω.
For single-ended 50
Ω applications, a 150Ω shunt match-
ing resistor to ground will result in the proper input
termination (Figure 1). For differential inputs there are
several termination options. If the input source is 50
Ω
differential, then input matching can be accomplished by
either a 100
Ω shunt resistor across the inputs (Figure 3),
or a 49.9
Ω shunt resistor on each of the inputs to ground
(Figure 2).
19934 F01
IF IN
LT1993-4
–INA
–INB
–OUT
+OUT
8
5
+INB
+INA
14
13
15
16
Figure 1. Input Termination for Single-Ended 50
Ω
Input Impedance
Figure 2. Input Termination for Differential 50
Ω Input Impedance
19934 F02
IF IN–
IF IN+
LT1993-4
–INA
–INB
–OUT
+OUT
8
5
+INB
+INA
14
13
15
16
Figure 3. Alternate Input Termination for Differential
50
Ω Input Impedance
19934 F03
IF IN–
IF IN+
LT1993-4
–INA
–INB
–OUT
+OUT
8
5
+INB
+INA
14
13
15
16
相关PDF资料 |
PDF描述 |
|---|---|
| LT1994MPDD#TRPBF | IC DIFF AMP/DRIVER LN 8-MSOP |
| LT1999MPS8-50#PBF | IC AMP CURR SENSE HV 8-MSOP |
| LT2079AIS#TRPBF | IC OPAMP MICROPOWER QUAD 14SOIC |
| LT2178CS8 | IC OPAMP MICROPOWER DUAL 8-SOIC |
| LT318AN8#PBF | IC OPAMP HI-SPEED 15MHZ 8-DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1993IUD-10 | 制造商:LINER 制造商全称:Linear Technology 功能描述:700MHz Low Distortion, Low Noise Differential Amplifi er/ADC Driver (AV = 10V/V) |
| LT1993IUD-10#PBF | 功能描述:IC DIFF AMP/ADC DRVR 16-QFN RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:73 系列:Over-The-Top® 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.07 V/µs 增益带宽积:200kHz -3db带宽:- 电流 - 输入偏压:1nA 电压 - 输入偏移:285µV 电流 - 电源:50µA 电流 - 输出 / 通道:25mA 电压 - 电源，单路/双路(±):2 V ~ 44 V，±1 V ~ 22 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-WFDFN 裸露焊盘 供应商设备封装:16-DFN-EP（5x3） 包装:管件 |
| LT1993IUD-10#TRPBF | 功能描述:IC DIFF AMP/ADC DRVR 16-QFN RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:73 系列:Over-The-Top® 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.07 V/µs 增益带宽积:200kHz -3db带宽:- 电流 - 输入偏压:1nA 电压 - 输入偏移:285µV 电流 - 电源:50µA 电流 - 输出 / 通道:25mA 电压 - 电源，单路/双路(±):2 V ~ 44 V，±1 V ~ 22 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-WFDFN 裸露焊盘 供应商设备封装:16-DFN-EP（5x3） 包装:管件 |
| LT1993IUD-2 | 制造商:Linear Technology 功能描述:SP Amp DIFF AMP Single 5.5V 16-Pin QFN EP |
| LT1993IUD-2#PBF | 功能描述:IC DIFF AMP/ADC DRVR 16-QFN RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1 系列:- 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.028 V/µs 增益带宽积:105kHz -3db带宽:- 电流 - 输入偏压:3nA 电压 - 输入偏移:100µV 电流 - 电源:3.3µA 电流 - 输出 / 通道:12mA 电压 - 电源，单路/双路(±):2.7 V ~ 12 V，±1.35 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:剪切带 (CT) 其它名称:OP481GRUZ-REELCT |
发布紧急采购，3分钟左右您将得到回复。