- 您现在的位置：买卖IC网 > PDF目录5272 > LT1999CS8-20#TRPBF (Linear Technology)IC AMP CURR SENSE HV 8-SOIC PDF资料下载
参数资料
| 型号： | LT1999CS8-20#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 7/24页 |
| 文件大小： | 0K |
| 描述： | IC AMP CURR SENSE HV 8-SOIC |
| 标准包装： | 2,500 |
| 放大器类型： | 电流检测 |
| 电路数： | 1 |
| 输出类型： | 带缓冲 |
| 转换速率： | 3 V/µs |
| -3db带宽： | 2MHz |
| 电流 - 输入偏压： | 137.5µA |
| 电压 - 输入偏移： | 500µV |
| 电流 - 电源： | 5.8mA |
| 电流 - 输出 / 通道： | 40mA |
| 电压 - 电源，单路/双路(±)： | 4.5 V ~ 5.5 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SO |
| 包装： | 带卷 (TR) |
LT1999-10/LT1999-20/
LT1999-50
15
1999fb
applicaTions inForMaTion
Input Common Mode Range
The LT1999 was optimized for high common mode re-
jection. Its input stage is balanced and fully differential,
designedtoamplifydifferentialsignalsandrejectcommon
mode signals. There is negligible crossover distortion due
to sense voltage reversals. The amplifier is most linear in
the zero-sense region.
With the V+ supply configured within the specified and
tested range (4.5V < V+ < 5.5V), the LT1999’s common
mode range extends from –5V to 80V. Pushing +IN and
–IN beyond the limits specified in the Absolute Maximum
table can turn on the voltage clamps designed to protect
the +IN and –IN pins during ESD events.
It is possible to operate the LT1999 on power supplies
as low as 4V (although it is not tested or specified below
4.5V). Operating the LT1999 on supplies below 4V will
produce erratic behavior. When operating the LT1999
with supplies as low as 4V, the common mode range for
inputs which extend below GND is reduced. Refer to the
Block Diagram (Figure 1). For inputs driven below V+,
diode D1 conducts. For proper operation, the input to the
transconductor V(G+IN) must be biased at approximately
2.25V above the GND pin. V(G+IN) sits on the centertap
of a voltage divider comprised of R+S and R+IN V(G–IN)
likewise sits in the middle of the voltage divider comprised
of R–S , and R–IN). The voltage on V(G+IN) input is given
by the following equation:
V(G+IN)= V +IN
R+S
R+S + R+IN
+ V+ VD1
(
) R+IN
R+S + R+IN
Setting V(G+IN) = 2.25V, the ratio (R+IN/R+S) to 5, and VD1
equal to 0.8V (cold temperatures), a plot of the lower input
common mode range plotted against supply is shown in
Figure 3.
Output Common Mode Range
The LT1999’s output common mode level is set by the
voltage on the REF pin. The REF pin sits in the middle of
a 160k to 160k voltage divider connected between V+ and
GND which sets the default open circuit potential of the
REF pin to mid-supply. It can be overdriven by an external
voltage source capable of driving 80k tied to a mid-supply
potential. See the Electrical Characteristics table for the
REF pin’s specified input voltage range.
Differential sampling of the OUT pin with respect the REF
pin provides the best noise immunity. Measurements of
the output voltage made differentially with respect to the
REF pin will provide the highest power supply and com-
mon mode rejection. Otherwise, power supply or GND pin
disturbances are divided by the REF pin’s voltage divider
and appear directly at the noninverting input of the trans-
resistance amplifier AO and are not rejected.
If not driven by a low impedance (<100Ω), the REF pin
should be filtered with at least 1nF of capacitance to a
low impedance, low noise ground plane. This external
capacitance will also provide a charge reservoir during
high frequency sampling of the REF pin by ADC inputs
attached to this pin.
Figure 3. Lower Input Common Mode vs Supply Voltage
SUPPLY VOLTAGE (V)
4
V CM(LOWER
LIMIT)
(V)
–2.0
–2.5
–3.0
–4.0
–5.0
–3.5
–4.5
–5.5
–6.0
4.75
4.25
5.25
1999 F03
5.5
4.5
5
BELOW GROUND INPUT
COMMON MODE RANGE
LIMITED BY V+
SUPPLY VOLTAGE
BELOW GROUND INPUT
COMMON MODE RANGE
LIMITED BY ESD CLAMPS
TYPICAL ESD CLAMP VOLTAGE
相关PDF资料 |
PDF描述 |
|---|---|
| 0031.8568 | FUSE 3.15A 250VAC 5X20 FAST |
| 0034.1737 | FUSE 125MA 250V 6.3X32 FAST GLSS |
| 0001.1026 | FUSE 1.6A 250V 6.3X32 FAST-ACT |
| TA45-ABDBHJ10C0 | CIRCUIT BRKR THERMAL 1A 2POLE |
| 0001.1027 | FUSE 2A 250V 6.3X32 FAST-ACT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1999CS8-50#PBF | 功能描述:IC OP AMP CURRENT SENSE 8-SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 产品培训模块:Differential Circuit Design Techniques for Communication Applications 标准包装:1 系列:- 放大器类型:RF/IF 差分 电路数:1 输出类型:差分 转换速率:9800 V/µs 增益带宽积:- -3db带宽:2.9GHz 电流 - 输入偏压:3µA 电压 - 输入偏移:- 电流 - 电源:40mA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-VQFN 裸露焊盘，CSP 供应商设备封装:16-LFCSP-VQ 包装:剪切带 (CT) 产品目录页面:551 (CN2011-ZH PDF) 其它名称:ADL5561ACPZ-R7CT |
| LT1999CS8-50#TRPBF | 功能描述:IC AMP CURR SENSE HV 8-SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:通用 电路数:2 输出类型:满摆幅 转换速率:1.8 V/µs 增益带宽积:6.5MHz -3db带宽:4.5MHz 电流 - 输入偏压:5nA 电压 - 输入偏移:100µV 电流 - 电源:65µA 电流 - 输出 / 通道:35mA 电压 - 电源，单路/双路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| LT1999HMS8-10 | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Voltage, Bidirectional Current Sense Amplifier Low Power Shutdown <10μA |
| LT1999HMS8-10#PBF | 功能描述:IC OP AMP CURRENT SENSE 8MSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:100 系列:- 放大器类型:通用 电路数:1 输出类型:- 转换速率:0.2 V/µs 增益带宽积:- -3db带宽:- 电流 - 输入偏压:100pA 电压 - 输入偏移:30µV 电流 - 电源:380µA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):±2 V ~ 18 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SO 包装:管件 |
| LT1999HMS8-10#TRPBF | 功能描述:IC OP AMP CURRENT SENSE 8MSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:100 系列:- 放大器类型:通用 电路数:1 输出类型:- 转换速率:0.2 V/µs 增益带宽积:- -3db带宽:- 电流 - 输入偏压:100pA 电压 - 输入偏移:30µV 电流 - 电源:380µA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):±2 V ~ 18 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SO 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。