参数资料
| 型号： | LT3060IDC-5#TRMPBF |
| 厂商： | Linear Technology |
| 文件页数： | 15/26页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 5V .1A 8DFN |
| 标准包装： | 500 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 5V |
| 输入电压： | 最高 45 V |
| 电压 - 压降（标准）： | 0.3V @ 100mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 100mA |
| 电流 - 限制（最小）： | 110mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-WFDFN 裸露焊盘 |
| 供应商设备封装： | 8-DFN（2x2） |
| 包装： | 带卷 (TR) |
LT3060 Series
PIN FUNCTIONS
(DC8/TS8)
REF/BYP (Pin 1/Pin 8): Reference/Bypass. Connecting
a single capacitor from this pin to GND bypasses the
LT3060’s reference noise and soft-starts the reference.
A 10nF bypass capacitor typically reduces output voltage
noise to 30μV RMS in a 10Hz to 100kHz bandwidth. Soft-
start time is directly proportional to the REF/BYP capacitor
value. If the LT3060 is placed in shutdown, REF/BYP is
actively pulled low by an internal device to reset soft-start.
If low noise or soft-start performance is not required, this
pin must be left floating (unconnected). Do not drive this
pin with any active circuitry.
ADJ (Pin 2/Pin 7): Adjust. This pin is the error ampli-
fier’s inverting terminal. It’s typical bias current of 15nA
flows out of the pin (see curve of ADJ Pin Bias Current vs
Temperature in the Typical Performance Characteristics
section). The ADJ pin voltage is 600mV referenced to GND.
Connecting a capacitor from ADJ to OUT reduces output
noise and improves transient response for output voltages
greater than 600mV. See the Applications Information sec-
tion for calculating the value of the feedforward capacitor.
For fixed voltage versions of the LT3060, if low noise and
fast transient response is not required, this pin must be
left floating (unconnected).
OUT (Pins 3, 4/Pin 6): Output. These pin(s) supply power to
the load. Stability requirements demand a minimum 2.2μF
ceramic output capacitor to prevent oscillations. Large
load transient applications require larger output capaci-
tors to limit peak voltage transients. See the Applications
Information section for details on transient response and
reverse output characteristics. Permissible output voltage
range is 600mV to 44.5V.
IN (Pins 5, 6/Pin 5): Input. These pin(s) supply power to
the device. The LT3060 requires a local IN bypass capacitor
if it is located more than six inches from the main input
filter capacitor. In general, battery output impedance rises
with frequency, so adding a bypass capacitor in battery-
powered circuits is advisable.
An input bypass capacitor in the range of 1μF to 10μF
suffices. The LT3060 withstands reverse voltages on the
IN pin with respect to its GND and OUT pins. In a reversed
input situation, such as a battery plugged in backwards,
the LT3060 behaves as if a large resistor is in series with
its input. Limited reverse current flows into the LT3060
and no reverse voltage appears at the load. The device
protects itself and the load.
SHDN (Pin 7/Pin 1): Shutdown. Pulling the SHDN pin
low puts the LT3060 into a low power state and turns
the output off. Drive the SHDN pin with either logic or an
open collector/drain with a pull-up resistor. The resistor
supplies the pull-up current to the open collector/drain
logic, normally several microamperes, and the SHDN
pin current, typically less than 3μA. If unused, connect
the SHDN pin to IN. The LT3060 does not function if the
SHDN pin is not connected. The SHDN pin cannot be
driven below GND unless tied to the IN pin. If the SHDN
pin is driven below GND while IN is powered, the output
may turn on. SHDN pin logic cannot be referenced to a
negative supply voltage.
GND (Pin 8, Exposed Pad Pin 9/Pins 2, 3, 4): Ground.
For the adjustable LT3060, connect the bottom of the ex-
ternal resistor divider that sets the output voltage directly
to GND for optimum regulation. For the DFN package, tie
exposed pad Pin 9 directly to Pin 8 and the PCB ground.
This exposed pad provides enhanced thermal performance
with its connection to the PCB ground. See the Applica-
tions Information section for thermal considerations and
calculating junction temperature.
3060fb
15
相关PDF资料 |
PDF描述 |
|---|---|
| RMC30DREH-S93 | CONN EDGECARD 60POS .100 EYELET |
| LT3060IDC-3.3#TRPBF | IC REG LDO 3.3V .1A 8DFN |
| LT3060IDC-3.3#TRMPBF | IC REG LDO 3.3V .1A 8DFN |
| LT3060IDC-2.5#TRPBF | IC REG LDO 2.5V .1A 8DFN |
| ACC26DRYS | CONN EDGECARD 52POS .100 DIP SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3060IDCPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:45V VIN, Micropower, Low Noise, 100mA Low Dropout, Linear Regulator |
| LT3060IDCTR | 制造商:LINER 制造商全称:Linear Technology 功能描述:45V VIN, Micropower, Low Noise, 100mA Low Dropout, Linear Regulator |
| LT3060IDCTRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:45V VIN, Micropower, Low Noise, 100mA Low Dropout, Linear Regulator |
| LT3060ITS8 | 制造商:LINER 制造商全称:Linear Technology 功能描述:45V VIN, Micropower, Low Noise, 100mA Low Dropout, Linear Regulator |
| LT3060ITS8#PBF | 制造商:Linear Technology 功能描述:LDO Regulator Pos 0.6V to 44.5V 0.1A 8-Pin TSOT-23 |
发布紧急采购，3分钟左右您将得到回复。