参数资料
| 型号： | LT3080IST#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 13/28页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO ADJ 1.1A SOT223-3 |
| 标准包装： | 2,500 |
| 稳压器拓扑结构： | 正，可调式 |
| 输出电压： | 可调至 36V |
| 输入电压： | 1.2 V ~ 36 V |
| 电压 - 压降（标准）： | 1.35V @ 1.1A |
| 稳压器数量： | 1 |
| 电流 - 输出： | 1.1A |
| 电流 - 限制（最小）： | 1.1A |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | TO-261-4，TO-261AA |
| 供应商设备封装： | SOT-223-3 |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LT3080
APPLICATIONS INFORMATION
from the error amplifier must be considered, and the gain
created by using a resistor divider cannot be forgotten.
Traditional low noise regulators bring the voltage refer-
ence out to an external pin (usually through a large value
resistor) to allow for bypassing and noise reduction of
reference noise. The LT3080 does not use a traditional
voltage reference like other linear regulators, but instead
uses a reference current. That current operates with typi-
cal noise current levels of 3.2pA/√ Hz (1nA RMS over the
10Hz to 100kHz bandwidth). The voltage noise of this
is equal to the noise current multiplied by the resistor
value. The resistor generates spot noise equal to √ 4kTR
(k = Boltzmann’s constant, 1.38 ? 10 –23 J/°K, and T is
absolute temperature) which is RMS summed with the
reference current noise. To lower reference noise, the
voltage setting resistor may be bypassed with a capacitor,
though this causes start-up time to increase as a factor
of the RC time constant.
The LT3080 uses a unity-gain follower from the SET pin
to drive the output, and there is no requirement to use
a resistor to set the output voltage. Use a high accuracy
voltage reference placed at the SET pin to remove the er-
rors in output voltage due to reference current tolerance
and resistor tolerance. Active driving of the SET pin is
acceptable; the limitations are the creativity and ingenuity
of the circuit designer.
One problem that a normal linear regulator sees with refer-
ence voltage noise is that noise is gained up along with the
output when using a resistor divider to operate at levels
higher than the normal reference voltage. With the LT3080,
the unity-gain follower presents no gain whatsoever from
the SET pin to the output, so noise figures do not increase
accordingly. Error amplifier noise is typically 125nV/√ Hz
(40μV RMS over the 10Hz to 100kHz bandwidth); this is
another factor that is RMS summed in to give a final noise
figure for the regulator.
current limit as the input-to-output voltage increases and
keeps the power dissipation at safe levels for all values
of input-to-output voltage. The LT3080 provides some
output current at all values of input-to-output voltage up
to the device breakdown. See the Current Limit curve in
the Typical Performance Characteristics.
When power is first turned on, the input voltage rises and
the output follows the input, allowing the regulator to start
into very heavy loads. During start-up, as the input voltage
is rising, the input-to-output voltage differential is small,
allowing the regulator to supply large output currents.
With a high input voltage, a problem can occur wherein
removal of an output short will not allow the output volt-
age to recover. Other regulators, such as the LT1085 and
LT1764A, also exhibit this phenomenon so it is not unique
to the LT3080.
The problem occurs with a heavy output load when the
input voltage is high and the output voltage is low. Com-
mon situations are immediately after the removal of a
short circuit. The load line for such a load may intersect
the output current curve at two points. If this happens,
there are two stable operating points for the regulator.
With this double intersection, the input power supply may
need to be cycled down to zero and brought up again to
make the output recover.
Load Regulation
Because the LT3080 is a floating device (there is no ground
pin on the part, all quiescent and drive current is delivered
to the load), it is not possible to provide true remote load
sensing. Load regulation will be limited by the resistance
IN LT3080
V CONTROL
Curves in the Typical Performance Characteristics show
noise spectral density and peak-to-peak noise character-
istics for both the reference current and error amplifier
over the 10Hz to 100kHz bandwidth.
+
–
SET R SET
OUT
PARASITIC
RESISTANCE
R P
R P
LOAD
Overload Recovery
R P
3080 F07
Like many IC power regulators, the LT3080 has safe operat-
ing area (SOA) protection. The SOA protection decreases
Figure 7. Connections for Best Load Regulation
3080fc
13
相关PDF资料 |
PDF描述 |
|---|---|
| MIC69301-1.2WR TR | IC REG LDO 1.2V 3A SPAK |
| LT1175CN8 | IC REG LDO NEG ADJ .5A 8-DIP |
| HBC60DRTS | CONN EDGECARD 120PS DIP .100 SLD |
| ESC43DRYS | CONN EDGECARD 86POS DIP .100 SLD |
| ASC05DTEN | CONN EDGECARD 10POS .100 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3080IT#PBF | 功能描述:IC REG LDO ADJ 1.1A TO-220-5 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:3V 输入电压:2.3 V ~ 5.5 V 电压 - 压降（标准）:0.035V @ 150mA 稳压器数量:2 电流 - 输出:150mA 电流 - 限制（最小）:300mA 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-UFDFN 裸露焊盘，6-TMLF? 供应商设备封装:6-TMLF?（1.6x1.6） 包装:Digi-Reel® 产品目录页面:1104 (CN2011-ZH PDF) 其它名称:576-3018-6 |
| LT3080IT#TRPBF | 功能描述:IC REG LDO ADJ 1.1A TO-220-5 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:4V 输入电压:最高 16V 电压 - 压降（标准）:0.28V @ 150mA 稳压器数量:1 电流 - 输出:150mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:5-VFBGA 供应商设备封装:5-uSMD 包装:Digi-Reel® 其它名称:LP2985AIBP-4.0DKR |
| LT3081 | 制造商:LINEAR_DIMENSIONS 制造商全称:LINEAR_DIMENSIONS 功能描述:1.5A Single Resistor Rugged Linear Regulator with Monitors |
| LT-30814 | 制造商:Datak Corporation 功能描述: |
| LT3081EDF#PBF | 制造商:Linear Technology 功能描述:IC REG LDO ADJ 1.5A 12DFN 制造商:Linear Technology 功能描述:IC LDO LINEAR REG RUGGED 1.5 制造商:Linear Technology 功能描述:IC, LDO LINEAR REG, RUGGED 1.5A, 12DFN 制造商:Linear Technology 功能描述:LDO, ADJ, 0V-34.5V, 1.5A, DFN-12, Input Voltage Min:1.2V, Input Voltage Max:36V, 制造商:Linear Technology 功能描述:LDO, ADJ, 0V-34.5V, 1.5A, DFN-12, Input Voltage Min:1.2V, Input Voltage Max:36V, Output Voltage Min:0V, Output Voltage Max:34.5V, Output Current:1.5A, Dropout Voltage Vdo:1.23V, No. of Pins:12, Operating Temperature Min:-40C , RoHS Compliant: Yes |
发布紧急采购，3分钟左右您将得到回复。