- 您现在的位置：买卖IC网 > PDF目录14870 > LT3467AES6#TRMPBF (Linear Technology)IC REG BOOST ADJ 1.1A TSOT23-6 PDF资料下载
参数资料
| 型号： | LT3467AES6#TRMPBF |
| 厂商： | Linear Technology |
| 文件页数： | 8/18页 |
| 文件大小： | 0K |
| 描述： | IC REG BOOST ADJ 1.1A TSOT23-6 |
| 标准包装： | 1 |
| 类型： | 升压（升压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 1.26 V ~ 40 V |
| 输入电压： | 2.4 V ~ 16 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 2.1MHz |
| 电流 - 输出： | 1.1A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-6 细型，TSOT-23-6 |
| 包装： | 标准包装 |
| 供应商设备封装： | TSOT-23-6 |
| 产品目录页面： | 1331 (CN2011-ZH PDF) |
| 其它名称： | LT3467AES6#TRMPBFDKR |
LT3467/LT3467A
APPLICATIONS INFORMATION
Capacitor Selection
Low ESR (equivalent series resistance) capacitors should
be used at the output to minimize the output ripple voltage.
Multi-layer ceramic capacitors are an excellent choice,
A phase lead zero can be intentionally introduced by placing
a capacitor (C4) in parallel with the resistor (R1) between
V OUT and V FB as shown in Figure 2. The frequency of the
zero is determined by the following equation.
as they have extremely low ESR and are available in very
small packages. X5R dielectrics are preferred, followed
by X7R, as these materials retain the capacitance over
? Z =
1
2 π ? R1? C4
wide voltage and temperature ranges. A 4.7μF to 15μF
output capacitor is suf?cient for most applications, but
systems with very low output currents may need only a
1μF or 2.2μF output capacitor. Solid tantalum or OS-CON
capacitors can be used, but they will occupy more board
area than a ceramic and will have a higher ESR. Always
use a capacitor with a suf?cient voltage rating.
Ceramic capacitors also make a good choice for the input
decoupling capacitor, which should be placed as close as
possible to the LT3467. A 1μF to 4.7μF input capacitor
is suf?cient for most applications. Table 2 shows a list
of several ceramic capacitor manufacturers. Consult the
manufacturers for detailed information on their entire
selection of ceramic parts.
Table 2. Ceramic Capacitor Manufacturers
By choosing the appropriate values for the resistor and
capacitor, the zero frequency can be designed to improve
the phase margin of the overall converter. The typical
target value for the zero frequency is between 35kHz
to 55kHz. Figure 3 shows the transient response of the
step-up converter from Figure 8 without the phase lead
capacitor C4. Although adequate for many applications,
phase margin is not ideal as evidenced by 2-3 “bumps”
in both the output voltage and inductor current. A 22pF
capacitor for C4 results in ideal phase margin, which is
revealed in Figure 4 as a more damped response and less
overshoot.
Diode Selection
A Schottky diode is recommended for use with the LT3467
and the LT3467A. The Philips PMEG 2005 is a very good
Taiyo Yuden
AVX
Murata
(408) 573-4150
(803) 448-9411
(714) 852-2001
www.t-yuden.com
www.avxcorp.com
www.murata.com
choice. Where the switch voltage exceeds 20V, use the
PMEG 3005 (a 30V diode). Where the switch voltage
exceeds 30V, use the PMEG 4005 (a 40V diode). These
The decision to use either low ESR (ceramic) capacitors
or the higher ESR (tantalum or OS-CON) capacitors can
affect the stability of the overall system. The ESR of any
capacitor, along with the capacitance itself, contributes
a zero to the system. For the tantalum and OS-CON ca-
pacitors, this zero is located at a lower frequency due to
the higher value of the ESR, while the zero of a ceramic
diodes are rated to handle an average forward current of
0.5A. In applications where the average forward current
of the diode exceeds 0.5A, a Philips PMEG 2010 rated at
1A is recommended. For higher ef?ciency, use a diode
with better thermal characteristics such as the On Semi-
conductor MBRM120 (a 20V diode) or the MBRM140 (a
40V diode).
capacitor is at a much higher frequency and can generally
be ignored.
3467afe
8
相关PDF资料 |
PDF描述 |
|---|---|
| PM3316-2R2M | INDUCTOR POWER 2.2UH SMD |
| ABM10DTAH-S189 | CONN EDGECARD 20POS R/A .156 SLD |
| ECO-S2DB122EA | CAP ALUM 1200UF 200V 20% SNAP |
| HCM18DRYN-S13 | CONN EDGECARD 36POS .156 EXTEND |
| HCM18DRYH-S13 | CONN EDGECARD 36POS .156 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3467AIDDB#TRMPBF | 功能描述:IC REG BOOST ADJ 1.1A 8DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| LT3467AIDDB#TRPBF | 功能描述:IC REG BOOST ADJ 1.1A 8DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| LT3467AIS6#PBF | 制造商:Linear Technology 功能描述:SP-SWREG/Monolithic, Cut Tape 1.1A, 2.1MHz Boost Converter |
| LT3467AIS6#TRMPBF | 功能描述:IC REG BOOST ADJ 1.1A TSOT23-6 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| LT3467AIS6#TRPBF | 功能描述:IC REG BOOST ADJ 1.1A TSOT23-6 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
发布紧急采购，3分钟左右您将得到回复。