- 您现在的位置：买卖IC网 > PDF目录14858 > LT3470ETS8#TRMPBF (Linear Technology)IC REG BUCK ADJ 0.2A TSOT23-8 PDF资料下载
参数资料
| 型号： | LT3470ETS8#TRMPBF |
| 厂商： | Linear Technology |
| 文件页数： | 13/20页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 0.2A TSOT23-8 |
| 标准包装： | 1 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 1.25 V ~ 16 V |
| 输入电压： | 4 V ~ 40 V |
| PWM 型： | Burst Mode? |
| 电流 - 输出： | 200mA |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-8 薄型，TSOT-23-8 |
| 包装： | 标准包装 |
| 供应商设备封装： | TSOT-23-8 |
| 产品目录页面： | 1331 (CN2011-ZH PDF) |
| 其它名称： | LT3470ETS8#TRMPBFDKR |
LT3470
APPLICATIONS INFORMATION
PCB Layout
For proper operation and minimum EMI, care must be
taken during printed circuit board layout. Note that large,
switched currents flow in the power switch, the internal
catch diode and the input capacitor. The loop formed by
these components should be as small as possible. Further-
more, the system ground should be tied to the regulator
ground in only one place; this prevents the switched cur-
rent from injecting noise into the system ground. These
components, along with the inductor and output capacitor,
should be placed on the same side of the circuit board,
and their connections should be made on that layer. Place
a local, unbroken ground plane below these components,
and tie this ground plane to system ground at one location,
SHDN
ideally at the ground terminal of the output capacitor C2.
Additionally, the SW and BOOST nodes should be kept as
small as possible. Unshielded inductors can induce noise
in the feedback path resulting in instability and increased
output ripple. To avoid this problem, use vias to route the
V OUT trace under the ground plane to the feedback divider
(as shown in Figure 5). Finally, keep the FB node as small
as possible so that the ground pin and ground traces
will shield it from the SW and BOOST nodes. Figure 5
shows component placement with trace, ground plane
and via locations. Include vias near the GND pin, or pad,
of the LT3470 to help remove heat from the LT3470 to
the ground plane.
SHDN
V IN
GND
C1
V IN
GND
VIAS TO FEEDBACK DIVIDER
VIAS TO LOCAL GROUND PLANE
C2
V OUT
V OUT
3470 F05
OUTLINE OF LOCAL GROUND PLANE
(5a)
(5b)
Figure 5. A Good PCB Layout Ensures Proper, Low EMI Operation
3470fd
13
相关PDF资料 |
PDF描述 |
|---|---|
| VI-27P-EY-F2 | CONVERTER MOD DC/DC 13.8V 50W |
| RGM15DTKS | CONN EDGECARD 30POS DIP .156 SLD |
| RMM08DTAN | CONN EDGECARD 16POS R/A .156 SLD |
| VI-27N-EY-F1 | CONVERTER MOD DC/DC 18.5V 50W |
| B41043A6228M | 2200UF 50V 18X40 SINGLE END |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3470HDDB | 制造商:LINER 制造商全称:Linear Technology 功能描述:Micropower Buck Regulator with Integrated Boost and Catch Diodes |
| LT3470HDDB#TRMPBF | 功能描述:IC REG BUCK ADJ 0.2A 8DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT3470HDDB#TRPBF | 功能描述:IC REG BUCK ADJ 0.2A 8DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT3470HTS8 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Micropower Buck Regulator with Integrated Boost and Catch Diodes |
| LT3470HTS8#PBF | 制造商:Linear Technology 功能描述:SP-SWREG/Monolithic, Cut Tape 300mA, 40V MicroPower Step-Down Regulator with Int |
发布紧急采购，3分钟左右您将得到回复。