- 您现在的位置：买卖IC网 > PDF目录20823 > LT3478IFE-1#TRPBF (Linear Technology)IC LED DRVR HP CONS CURR 16TSSOP PDF资料下载
参数资料
| 型号： | LT3478IFE-1#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 17/24页 |
| 文件大小： | 0K |
| 描述： | IC LED DRVR HP CONS CURR 16TSSOP |
| 标准包装： | 2,500 |
| 恒定电流： | 是 |
| 拓扑： | PWM，降压（降压），升压（升压） |
| 输出数： | 1 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 车载，背光 |
| 类型 - 次要： | 颜色，白色 LED |
| 频率： | 200kHz ~ 2.25MHz |
| 电源电压： | 2.8 V ~ 36 V |
| 输出电压： | 42V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm）裸露焊盘 |
| 供应商设备封装： | 16-TSSOP-EP |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 125°C |
LT3478/LT3478-1
APPLICATIO S I FOR ATIO
LT3478/LT3478-1 immediately stop switching, a soft-start
latch is set and the SS pin is discharged. The SS latch can
only be reset when V OUT falls below OVP and the SS pin
has been discharged below 0.25V (Figure 11). If the LED(s)
simply go open circuit and are reconnected, however, the
OVP used to protect the switch might be too high for the
reconnected LED(s). The LT3478/LT3478-1 therefore allow
OVP to be programmable to protect both the LED driver
switch and the LED(s). (The minimum allowable OVP for
normal operation for a given LED string depends on the
number of LEDs and their maximum forward voltage rat-
ings.) OVP is programmed using the OVPSET pin (front
page), given by,
OVP = (OVPSET ? 41)V
where the programmable range for the OVPSET pin is 0.3V
to 1V resulting in an OVP range of 12.3V to 41V.
The OVPSET pin can be programmed with a single resistor
by tapping off of the resistor divider from V REF used to
program CTRL1. If both CTRL1 and CTRL2 are connected
directly to V REF (maximum LED current setting) then OVP-
SET requires a simple 2 resistor divider from V REF .
Thermal Calculations
To maximize output power capability in an application
without exceeding the LT3478/LT3478-1 125°C maximum
operational junction temperature, it is useful to be able
to calculate power dissipation within the IC. The power
dissipation within the IC comes from four main sources:
switch DC loss, switch AC loss, Inductor and LED cur-
rent sensing and input quiescent current. These formulas
assume a boost converter architecture, continuous mode
operation and no PWM dimming.
(1) Switch DC loss = P SW(DC)
= (R SW ? I L(AVE)2 ? D)
R SW = switch resistance = 0.07 Ω (at T J = 125°C)
I L(AVE) = P OUT /( η ? V S )
P OUT = V OUT ? I LED
η = converter ef?ciency = P OUT /(P OUT + P LOSS )
V S = inductor supply input
D = switch duty cycle = (V OUT + V F – V S )/(V OUT + V F – V SAT )
V F = forward voltage drop of external Schottky diode
V SAT = I L(AVE) ? R SW
(2) Switch AC loss = P SW(AC)
= t EFF (1/2)I L(AVE) (V OUT + V F )(F OSC )
t EFF = effective switch current and switch V CE voltage
overlap time during turn on and turn off = 2 ? (t ISW +
t VSW )
t ISW = I SWITCH rise/fall time = I L(AVE) ? 2ns
t VSW = SW fall/rise time = (V OUT + V F ) ? 0.7ns
f OSC = switching frequency
(3) Current sensing loss = P SENSE =
P SENSE(IL) + P SENSE(ILED)
P SENSE(IL) = I L(AVE)2 ? 9.5m Ω
P SENSE(ILED) = I LED2 ? 0.1 Ω
(4) Input quiescent loss = P Q = V IN ? I Q where
I Q = (6.2mA + (100mA ? D))
Example (Using LT3478-1):
For V IN = V S = 8V, I LED = 700mA, V OUT = 24.5V (7 LEDs),
V F = 0.5V and f OSC = 0.2Mhz,
η = 0.89 (initial assumption)
I L(AVE) = (24.5 ? 0.7)/(0.89 ? 8) = 2.41A
D = (24.5 + 0.5 – 8)/(24.5 + 0.5 – 0.17) = 0.684
T EFF = 2 ? ((2.41 ? 2)ns + (24.5 + 0.5) ? 0.7)ns = 45ns
Total Power Dissipation:
P IC = P SW(DC) + P SW(AC) + P SENSE + P Q
P SW(DC) = 0.07 ? (2.41) 2 ? 0.684 = 0.278W
P SW(AC) = 45ns ? 0.5 ? 2.41 ? 25 ? 0.2MHz = 0.271W
P SENSE = ((2.41) 2 ? 0.0095) + ((0.7) 2 ? 0.1) = 0.104W
P Q = 8 ? (6.2mA + (100mA ? 0.684)) = 0.597W
P IC = 0.278 + 0.271 + 0.104 + 0.597 = 1.25W
34781f
17
相关PDF资料 |
PDF描述 |
|---|---|
| LT3599IFE#TRPBF | IC LED DRVR WHITE BCKLGT 28TSSOP |
| P51-15-S-O-M12-4.5V-000-000 | SENSOR 15PSI 7/16-20 UNF 2B 4.5V |
| P51-500-S-T-P-4.5OVP-000-000 | SENSOR 500PSI 7/16-20-2B .5-4.5V |
| P51-1000-S-H-P-5V-000-000 | SENSOR 1000PSIS M12 5V |
| REC5-4815SRW/H2/A/SMD/CTRL-R | CONV DC/DC 5W 36-72VIN 15VOUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3479 | 制造商:LINER 制造商全称:Linear Technology 功能描述:700mA Low Noise High Current LED Charge Pump |
| LT3479EDE | 制造商:Linear Technology 功能描述:Conv DC-DC Single Step Up 2.5V to 24V 14-Pin DFN EP |
| LT3479EDE#PBF | 功能描述:IC REG BOOST INV ADJ 3A 14DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LT3479EDE#PBF | 制造商:Linear Technology 功能描述:DC-DC CONVERTER CURRENT MODE 制造商:Linear Technology 功能描述:DC-DC CONVERTER, CURRENT MODE, 3.5MHZ, D |
| LT3479EDE#TRPBF | 功能描述:IC REG BOOST INV ADJ 3A 14DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
发布紧急采购，3分钟左右您将得到回复。