- 您现在的位置：买卖IC网 > PDF目录80121 > LT3483ES6#PBF (LINEAR TECHNOLOGY CORP) 0.23 A SWITCHING REGULATOR, PDSO6 PDF资料下载
参数资料
| 型号： | LT3483ES6#PBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | 0.23 A SWITCHING REGULATOR, PDSO6 |
| 封装： | LEAD FREE, PLASTIC, MO-193, TSOT-23, 6 PIN |
| 文件页数： | 9/12页 |
| 文件大小： | 875K |
| 代理商： | LT3483ES6#PBF |
LT3483/LT3483A
6
3483fc
OPERATION
CHOOSING A REGULATOR TOPOLOGY
Inverting Charge Pump
The inverting charge pump regulator combines an induc-
tor-based step-up with an inverting charge pump. This
configuration usually provides the best size, efficiency
and output ripple and is applicable where the magnitude of
VOUT is greater than VIN. Negative outputs to –38V can be
produced with the LT3483/LT3483A in this configuration.
For cases where the magnitude of VOUT is less than or
equaltoVIN,usea2-inductorortransformerconfiguration
such as the inverting flyback.
In the inverting charge pump configuration, a resistor
is added in series with the Schottky diode between the
negative output and the D pin of the LT3483/LT3483A. The
purpose of this resistor is to smooth/reduce the current
spike in the flying capacitor when the switch turns on. A
10Ω resistor works well for a Li+ to –8V application, and
the impact to converter efficiency is less than 3%. The
resistor values recommended in the applications circuits
also limit the switch current during a short-circuit condi-
tion at the output.
Inverting Flyback
Theinvertingflybackregulator,showninthe–5Vapplication
circuit, uses a coupled inductor and is an excellent choice
where the magnitude of the output is less than or equal
to the supply voltage. The inverting flyback also performs
well in a step-up/invert application, but it occupies more
board space compared with the inverting charge pump.
Also, the maximum |VOUT| using the flyback is less than
can be obtained with the charge pump—it is reduced from
38V by the magnitudes of VIN and ringing at the switch
node. Under a short-circuit condition at the output, a pro-
prietary technique limits the switch current and prevents
damage to the LT3483/LT3483A even with supply voltage
as high as 16V. As an option, a 0.47F capacitor may be
added between terminals D and SW of LT3483/LT3483A
to suppress ringing at SW.
Inductor Selection
Several recommended inductors that work well with the
LT3483/LT3483A are listed in Table 1, although there are
many other manufacturers and devices that can be used.
Consult each manufacturer for more detailed information
and for their entire selection of related parts. Many differ-
ent sizes and shapes are available. For inverting charge
pump regulators with input and output voltages below
7V, a 4.7H or 6.8H inductor is usually the best choice.
For flyback regulators or for inverting charge pump
regulators where the input or output voltage is greater
than 7V, a 10H inductor is usually the best choice. A
larger value inductor can be used to slightly increase the
available output current, but limit it to around twice the
The LT3483/LT3483A use a constant off-time control
scheme to provide high efficiency over a wide range of
output currents. Operation can be best understood by
referring to the Block Diagram. When the voltage at the
FB pin is approximately 0V, comparator A3 disables most
of the internal circuitry. Output current is then provided
by external capacitor COUT, which slowly discharges until
the voltage at the FB pin goes above the hysteresis point
of A3. Typical hysteresis at the FB pin is 10mV. A3 then
enables the internal circuitry, turns on power switch Q1,
and the currents in external inductors L1A and L1B be-
gin to ramp up. Once the switch current reaches 200mA
(LT3483) or 400mA (LT3483A), comparator A1 resets
the latch, which turns off Q1 after about 80ns. Inductor
current flows through the internal Schottky D1 to GND,
charging the flying capacitor. Once the 300ns off-time has
elapsed, and internal diode current drops below 250mA
(as detected by comparator A2), Q1 turns on again and
ramps up to the switch current limit. This switching action
continues until the output capacitor charge is replenished
(until the FB pin decreases to 0V), then A3 turns off the
internalcircuitryandthecyclerepeats.Theinvertingcharge
pump topology replaces L1B with the series combination
D2 and R2.
APPLICATIONS INFORMATION
相关PDF资料 |
PDF描述 |
|---|---|
| LK1601-7EPD2TB1 | 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE |
| LS1301-9EPD1T | 1-OUTPUT 100 W AC-DC REG PWR SUPPLY MODULE |
| LTC694CS-3.3 | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| LT1246IJ8 | SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, CDIP8 |
| LS1001-7RD6TB1 | 1-OUTPUT AC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3483ES6-TR | 制造商:LINER 制造商全称:Linear Technology 功能描述:Inverting Micropower DC/DC Converter with Schottky |
| LT3483ES6TRMPBF | 制造商:Linear Technology 功能描述:LTC3483 adj 200mA neg op dc-dc converter |
| LT3483ES6-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Inverting Micropower DC/DC Converter with Schottky |
| LT3483IDC#PBF | 制造商:Linear Technology 功能描述:SP-SWREG/Monolithic, Cut Tape 200mA, 40V Inverting COT DC/DC Converters with Int |
| LT3483IDC#TRMPBF | 功能描述:IC REG INV ADJ 0.2A 8DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
发布紧急采购，3分钟左右您将得到回复。