- 您现在的位置：买卖IC网 > PDF目录44984 > LT3485EDD-0#TRPBF (LINEAR TECHNOLOGY CORP) SPECIALTY ANALOG CIRCUIT, PDSO10 PDF资料下载
参数资料
| 型号： | LT3485EDD-0#TRPBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PDSO10 |
| 封装： | 3 X 3 MM, LEAD FREE, PLASTIC, MO-229WEED-2, DFN-10 |
| 文件页数： | 18/20页 |
| 文件大小： | 339K |
| 代理商： | LT3485EDD-0#TRPBF |
LT3485-0/LT3485-1/
LT3485-2/LT3485-3
7
34850123fb
CHARGE (Pin 1): Charge Pin. A low (<0.3V) to high (>1V)
transition on this pin puts the part into power delivery
mode. Once the target voltage is reached, the part will stop
charging the output. Toggle this pin to start charging
again. Bringing the pin low (<0.3V) will terminate the
power delivery and put the part in shutdown.
VBAT (Pin 2): Battery Supply Pin. Must be locally bypassed
with a good quality ceramic capacitor. Battery supply
must be 1.7V or higher.
VIN (Pin 3): Input Supply Pin. Must be locally bypassed
with a good quality ceramic capacitor. Input supply must
be 2.5V or higher.
SW (Pins 4, 5): Switch Pin. This is the collector of the
internal NPN power switch. Minimize the metal trace area
connected to this pin to minimize EMI. Tie one side of the
primary of the transformer to this pin. The target output
voltage is set by the turns ratio of the transformer.
Choose Turns Ratio N by the following equation:
N
VOUT
=
+ 2
31 5
.
where VOUT is the desired output voltage.
IGBTOUT (Pin 6): Output Drive for IGBT Gate. Connect
this pin to the gate of the IGBT.
IGBTIN (Pin 7): Logic Input Pin for IGBT Drive. When this
pin is driven higher than 1.5V, the IGBT output pin goes
high. When the pin is below 0.3V, the output is low.
IGBTPWR (Pin 8): Input Supply Pin. Must be locally
bypassed with a good quality ceramic capacitor. Input
supply must be 0.1V higher than the turn-on voltage for
the IGBT.
DONE (Pin 9): Open NPN Collector Indication Pin. When
target output voltage is reached, NPN turns on. This pin
needs a pull-up resistor or current source.
VMONT (Pin 10): Supplies a voltage proportional to the
output voltage where 1V is the end of charge voltage. Only
valid while the part is charging.
Exposed Pad (Pin 11): Ground. Tie directly to local
ground plane.
UU
U
PI FU CTIO S
相关PDF资料 |
PDF描述 |
|---|---|
| LT3485EDD-0#TR | SPECIALTY ANALOG CIRCUIT, PDSO10 |
| LT3493EDCB-3#TR | 2.2 A SWITCHING REGULATOR, 815 kHz SWITCHING FREQ-MAX, PDSO6 |
| LT3494EDDB#PBF | 0.25 A SWITCHING REGULATOR, PDSO8 |
| LT3494EDDB | 0.25 A SWITCHING REGULATOR, PDSO8 |
| LT3502AEDC#PBF | 1.1 A SWITCHING REGULATOR, 2800 kHz SWITCHING FREQ-MAX, PDSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3485EDD-1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Photoflash Capacitor Chargers with Output Voltage Monitor and Integrated IGBT Drive |
| LT3485EDD-1#PBF | 功能描述:IC CHARGER PHOTOFLASH 10-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 标准包装:1 系列:- 应用:手持/移动设备 电流 - 电源:- 电源电压:3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-LLP-EP（4x4） 包装:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名称:LP3905SD-30DKR |
| LT3485EDD-1#TRPBF | 功能描述:IC CHARGER PHOTOFLASH 10-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 标准包装:1 系列:- 应用:手持/移动设备 电流 - 电源:- 电源电压:3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-LLP-EP（4x4） 包装:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名称:LP3905SD-30DKR |
| LT3485EDD-2 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Photoflash Capacitor Chargers with Output Voltage Monitor and Integrated IGBT Drive |
| LT3485EDD-2#PBF | 功能描述:IC CHARGER PHOTOFLASH 10-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 标准包装:1 系列:- 应用:手持/移动设备 电流 - 电源:- 电源电压:3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-LLP-EP（4x4） 包装:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名称:LP3905SD-30DKR |
发布紧急采购，3分钟左右您将得到回复。