- 您现在的位置：买卖IC网 > PDF目录20627 > LT3500IDD#TRPBF (Linear Technology)IC REG DL BUCK/LINEAR 12-DFN PDF资料下载
参数资料
| 型号： | LT3500IDD#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 21/28页 |
| 文件大小： | 322K |
| 描述： | IC REG DL BUCK/LINEAR 12-DFN |
| 标准包装： | 2,500 |
| 拓扑： | 降压（降压）（1），线性（LDO）（1） |
| 功能： | 任何功能 |
| 输出数： | 2 |
| 频率 - 开关： | 500kHz ~ 2.4MHz |
| 电压/电流 - 输出 1： | 0.8 V ~ 38.9 V，2A |
| 电压/电流 - 输出 2： | 可调式，13mA |
| 带 LED 驱动器： | 无 |
| 带监控器： | 无 |
| 带序列发生器： | 无 |
| 电源电压： | 3 V ~ 36 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 12-WFDFN 裸露焊盘 |
| 供应商设备封装： | 12-DFN |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页
LT3500
21
3500fc
APPLICATIONS INFORMATION
The PG pin has a sink capability of 400糀 when the FB and
LFB pins are below the threshold and can withstand 40V
when the outputs are in regulation. The PG pin is typically
connected to the output with a resistor and is used as an
error ag. The resistor value should be chosen to allow the
PG voltage to drop below 0.4V in an error condition.
Example:
V
OUT1
= 5V, PGSINK
(MIN)
= 200糀
R
PG
= (5 0.4)/200糀 = 23k?/DIV>
The PG pin has a sink capability of 800糀 when the FB
and LFB pins are above the threshold and can withstand
40V when the outputs are not in regulation. The PG pin is
typically used as a drive signal for an output disconnect
device. The PG pull-up resistor should be sized in the
same manner as the PG pull-up resistor.
Linear Regulator
The LT3500 contains an error ampli er and a NPN output
device which can be con gured as a linear regulator or as
a linear regulator controller.
With the LFB and LDRV pins con gured as shown in
Figure 1, the LDRV pin outputs a regulated voltage with a
typical current limit of 13mA.
The LDRV voltage is programmed with a resistor divider
between the output and the LFB pin. Choose the 1% resis-
tors according to:
R3=R4
V
LDRV
0.8V
1
R4 should be 10.0k or less to avoid bias current errors.
Reference designators refer to the Block Diagram in
Figure 1.
The reference voltage for the linear regulator (LFB pin)
will track the SS pin in the same manner as the FB pin of
the switching regulator.
At power-up, a reset signal sets the soft-start latch and
discharges the SS pin to approximately 0V to ensure
proper start-up. When the SS pin is fully discharged the
latch is reset and the internal 2.75糀 current source starts
to charge the SS pin.
When the SS pin voltage is below 100mV, the V
C
pin is
pulled low which disables switching. As the SS pin voltage
rises above 100mV, the V
C
pin is released and the outputs
are regulated to the SS voltage. When the SS pin voltage
minus 100mV exceeds the internal 0.8V reference, the
outputs are regulated to the reference. The SS pin voltage
will continue to rise until it is clamped at 2V.
In the event of a V
IN
undervoltage lockout, the SHDN pin
driven below 0.8V, or the internal die temperature exceeding
its maximum rating during normal operation, the soft-start
latch is set, triggering a start-up sequence.
In addition, if the load exceeds the maximum output switch
current (switching regulator only), the output will start to
drop causing the V
C
pin clamp to be activated. As long as
the V
C
pin is clamped, the SS pin will be discharged. As
a result, the output will be regulated to the highest volt-
age that the maximum output current can support. For
example, if a 6V output is loaded by 1?the SS pin will
drop to 0.5V, regulating the output at 3V (typical current
limit time load, 3A " 1?. Once the overload condition is
removed, the output will soft-start from the temporary
voltage level to the normal regulation point.
Since the SS pin is clamped at 2V and has to discharge to
0.9V before taking control of regulation, momentary over-
load conditions will be tolerated without a soft-start recov-
ery. The typical time before the SS pin takes control is:
t
SS(CONTROL)
=
C
SS
"1.1V
600糀
Power Good Indicators
The PG and PG pins are collector outputs of an internal
comparator. The comparator compares the voltages of
the FB and LFB pins to 90% of the reference voltage with
30mV of hysterisis.
相关PDF资料 |
PDF描述 |
|---|---|
| 591D108X0004R2T20H | CAP TANT 1000UF 4V 20% 2824 |
| GBM10DTBT-S189 | CONN EDGECARD 20POS R/A .156 SLD |
| VI-2NX-EW-B1 | CONVERTER MOD DC/DC 5.2V 100W |
| VI-2NX-CX | CONVERTER MOD DC/DC 5.2V 75W |
| NMN1.00BK | NYLON MULTI 1" BLACK 200' |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3500IMSE#PBF | 功能描述:IC REG DL BUCK/LINEAR 16-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压（降压）同步（3），线性（LDO）（2） 功能:任何功能 输出数:5 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:5.6 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
| LT3500IMSE#TRPBF | 功能描述:IC REG DL BUCK/LINEAR 16-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压（降压）同步（3），线性（LDO）（2） 功能:任何功能 输出数:5 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:5.6 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
| LT3500IMSE-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Monolithic 2A Step-Down Regulator Plus Linear Regulator/Controller |
| LT3500IMSE-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Monolithic 2A Step-Down Regulator Plus Linear Regulator/Controller |
| LT3500T | 制造商:Eaton Corporation 功能描述:TYPE LT TRIP UNIT ONLY 3P 500A 600VAC MAX |
发布紧急采购，3分钟左右您将得到回复。