- 您现在的位置：买卖IC网 > PDF目录20624 > LT3500IMSE#TRPBF (Linear Technology)IC REG DL BUCK/LINEAR 16-MSOP PDF资料下载
参数资料
| 型号： | LT3500IMSE#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 18/28页 |
| 文件大小： | 322K |
| 描述： | IC REG DL BUCK/LINEAR 16-MSOP |
| 标准包装： | 2,500 |
| 拓扑： | 降压（降压）（1），线性（LDO）（1） |
| 功能： | 任何功能 |
| 输出数： | 2 |
| 频率 - 开关： | 500kHz ~ 2.4MHz |
| 电压/电流 - 输出 1： | 0.8 V ~ 38.9 V，2A |
| 电压/电流 - 输出 2： | 可调式，13mA |
| 带 LED 驱动器： | 无 |
| 带监控器： | 无 |
| 带序列发生器： | 无 |
| 电源电压： | 3 V ~ 36 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TFSOP（0.118"，3.00mm 宽）裸露焊盘 |
| 供应商设备封装： | 16-MSOP，裸露焊盘 |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LT3500
18
3500fc
The boost circuit can also run directly from a DC voltage
that is higher than the input voltage by more than 2.5V, as
in Figure 5d. The diode is used to prevent damage to the
LT3500 in case V
X
is held low while V
IN
is present. The
circuit eliminates a capacitor, but ef ciency may be lower
and dissipation in the LT3500 may be higher. Also, if V
X
is
absent, the LT3500 will still attempt to regulate the output,
but will do so with very low ef ciency and high dissipation
because the switch will not be able to saturate, dropping
1.5V to 2V in conduction.
The minimum input voltage of an LT3500 application is
limited by the minimum operating voltage (<2.8V) and by
the maximum duty cycle as outlined above. For proper
start-up, the minimum input voltage is also limited by
the boost circuit. If the input voltage is ramped slowly, or
the LT3500 is turned on with its SS pin when the output
is already in regulation, then the boost capacitor may not
be fully charged. Because the boost capacitor is charged
with the energy stored in the inductor, the circuit will rely
on some minimum load current to get the boost circuit
running properly. This minimum load will depend on
input and output voltages and on the arrangement of the
boost circuit.
The Typical Performance Characteristics section shows
plots of the minimum load current to start and to run as a
function of input voltage for 3.3V and 5V outputs. In many
cases the discharged output capacitor will present a load
to the switcher which will allow it to start. The plots show
the worst-case situation where V
IN
is ramping very slowly.
Use a Schottky diode for the lowest start-up voltage.
Frequency Compensation
The LT3500 uses current mode control to regulate the
output. This simpli es loop compensation. In particular, the
LT3500 does not require the ESR of the output capacitor
for stability so you are free to use ceramic capacitors to
achieve low output ripple and small circuit size. Frequency
compensation is provided by the components tied to the
V
C
pin. Generally a capacitor and a resistor in series to
ground determine loop gain. In addition, there is a lower
value capacitor in parallel. This capacitor is not part of
the loop compensation but is used to lter noise at the
switching frequency.
Loop compensation determines the stability and transient
performance. Designing the compensation network is a bit
complicated and the best values depend on the application
and in particular the type of output capacitor. A practical
approach is to start with one of the circuits in this data
sheet that is similar to your application and tune the com-
pensation network to optimize the performance. Stability
should then be checked across all operating conditions,
including load current, input voltage and temperature.
The LT1375 data sheet contains a more thorough discus-
sion of loop compensation and describes how to test the
stability using a transient load.
Figure 6 shows an equivalent circuit for the LT3500 control
loop. The error amp is a transconductance ampli er with
nite output impedance. The power section, consisting
of the modulator, power switch, and inductor, is modeled
as a transconductance ampli er generating an output
APPLICATIONS INFORMATION
Figure 6. Model for Loop Response
SW
LT3500
FB
V
C
0.8V
C
F
C
PL
V
OUT1
C1
C1
3500 F06
C
C
R
C
R1
ESR
TANTALUM
OR
POLYMER
CERAMIC
R2
4M
ERROR AMP
g
m
= 250糾hos
CURRENT MODE
POWER STAGE
g
m
= 3mho
相关PDF资料 |
PDF描述 |
|---|---|
| GEM06DCMI-S288 | CONN EDGECARD 12POS .156 EXTEND |
| F951A336MQAAQ2 | CAP TANT 33UF 10V 20% 1206 |
| GBM22DSXN | CONN EDGECARD 44POS DIP .156 SLD |
| 591D477X06W3R2T20H | CAP TANT 470UF 6.3V 20% 2824 |
| GSA50DTAZ-S664 | CONN EDGECARD 100PS R/A .125 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3500T | 制造商:Eaton Corporation 功能描述:TYPE LT TRIP UNIT ONLY 3P 500A 600VAC MAX |
| LT3501 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Monolithic Dual Tracking 3A Step-Down Switching Regulator |
| LT3501_12 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Monolithic Dual Tracking 3A Step-Down Switching |
| LT3501EFE | 制造商:Linear Technology 功能描述:Conv DC-DC Dual Step Down 3.1V to 25V 20-Pin TSSOP EP |
| LT3501EFE#PBF | 功能描述:IC REG BUCK ADJ 3A DL 20TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
发布紧急采购，3分钟左右您将得到回复。