- 您现在的位置：买卖IC网 > PDF目录20621 > LT3507IUHF#TRPBF (Linear Technology)IC REG QD BUCK/LINEAR 38-QFN PDF资料下载
参数资料
| 型号： | LT3507IUHF#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 7/28页 |
| 文件大小： | 302K |
| 描述： | IC REG QD BUCK/LINEAR 38-QFN |
| 产品培训模块： | More Information on LDOs |
| 标准包装： | 2,500 |
| 拓扑： | 降压（降压）（1），线性（LDO）（1） |
| 功能： | 任何功能 |
| 输出数： | 4 |
| 频率 - 开关： | 900kHz ~ 1.1MHz |
| 电压/电流 - 输出 1： | 0.8 V ~ 32.4 V，2.4A |
| 电压/电流 - 输出 2： | 0.8 V ~ 32.4 V，1.5A |
| 电压/电流 - 输出 3： | 0.8 V ~ 32.4 V，1.5A |
| 带 LED 驱动器： | 无 |
| 带监控器： | 无 |
| 带序列发生器： | 是 |
| 电源电压： | 4 V ~ 36 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 38-WFQFN 裸露焊盘 |
| 供应商设备封装： | 38-QFN（5x7） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LT3507
7
3507fa
PIN FUNCTIONS
BOOST1, BOOST2, BOOST3 (Pins 1, 27, 32): The BOOST
pins are used to provide drive voltages, higher than the
input voltage, to the internal bipolar NPN power switches.
These pins must be tied through a diode from V
OUT
, V
IN
or another supply greater than 2.5V.
V
IN1
(Pins 2, 3): The V
IN1
pins supply power to the internal
switch of the 2.4A regulator and to the LT3507s internal
reference and start-up circuitry. These pins must be locally
bypassed (Note 6).
V
INSW
(Pin 4): The V
INSW
pin is a switched V
IN1
for the
user programmable undervoltage and overvoltage detec-
tion. It is connected to V
IN1
when any of the RUN pins
are pulled high, and high impedance when all RUN pins
are low or open.
OVLO (Pin 5): The LT3507 goes into overvoltage shutdown
when this pin goes above 1.2V. If unused, the OVLO pin
should be tied to GND.
UVLO (Pin 6): The LT3507 goes into undervoltage shutdown
when this pin drops below 1.2V. If unused, the UVLO pin
should be tied to V
INSW
.
V
C1
, V
C2
, V
C3
(Pins 7, 23, 19): The V
C
pins are the outputs
of the internal error amps. The voltages on these pins
control the peak switch currents. These pins are normally
used to compensate the control loops. Each switching
regulator can be shut down by pulling its respective V
C
pin to ground with an NMOS or NPN transistor.
TRK/SS1, TRK/SS2, TRK/SS3, TRK/SS4 (Pins 8, 21, 18,
26): The TRK/SS pins allow a regulator to track the output
of another regulator. When the TRK/SS pin is below 0.8V,
the FB pin regulates to the TRK/SS voltage. This pin can
also be used as a soft-start by connecting a capacitor from
TRK/SS to ground. The TRK/SS pins should be left open
if neither feature is used.
FB1, FB2, FB3 (Pins 9, 22, 20): The FB pins are the nega-
tive inputs of the error ampli ers. The LT3507 regulates
each feedback pin to the lesser of 0.8V or the TRK/SS
pin voltage. Connect the feedback resistor divider taps
to these pins.
Note 6: V
INX
pins that are connected together may share a bypass capacitor.
PGOOD1, PGOOD2, PGOOD3 (Pins 10, 11, 12): The
PGOOD pins are the open-collector outputs of an internal
comparator. PGOOD remains low until the FB pin is within
10% of the nal regulation voltage. As well as indicating
output regulation, the PGOOD pins can sequence the
switching regulators. These pins must be left unconnected
if unused. The PGOOD outputs are valid when V
IN
is greater
than 3.5V and any of the RUN pins are high. They are not
valid when all RUN pins are low.
R
T
/SYNC (Pin 13): The R
T
/SYNC pin requires a resistor
to ground or a clock signal to set the operating frequency
of the LT3507.
RUN1, RUN2, RUN3 (Pins 14, 15, 16): The RUN pins are
used to shut down the individual switching regulators.
When all three RUN pins are low, the LT3507 shuts down
and draws less than 1糀 from V
IN1
.
BIAS (Pin 17): The BIAS pin supplies the current to the
LT3507s internal regulator. This pin should be tied to the
lowest available voltage source above 3V (either V
IN
, V
OUT
or any other available supply). The LDO pass transistors
base current is supplied from the BIAS pin if it is at least
0.8V above the LDO DRIVE output.
DRIVE (Pin 24): The DRIVE pin provides the base drive for
an external NPN transistor used for the LDO regulator.
FB4 (Pin 25): The FB4 pin is the negative input to the LDO
error ampli er. It is regulated to 0.8V through the LDO
feedback resistor divider.
V
IN2
(Pins 30, 31)/V
IN3
(Pins 35, 36 ): The V
IN2
and V
IN3
pins supply power to the internal switches of the 1.5A con-
verters. These pins must be locally bypassed (Note 6).
SW1 (Pins 37, 38)/SW2 (Pins 28, 29)/SW3 (Pins 33,
34): The SW pins are the outputs of the internal power
switches. Connect these pins to the inductors and switch-
ing diodes.
Exposed Pad (Pin 39): Ground. The underside Exposed
Pad metal of the package provides both electrical contact
to ground and good thermal contact to the printed circuit
board. The Exposed Pad must be soldered to a grounded
pad on the circuit board for proper operation.
相关PDF资料 |
PDF描述 |
|---|---|
| TH3D107M010D0600 | CAP TANT 100UF 10V 20% 2917 |
| R1D-1515/HP | CONV DC/DC 1W 15VIN +/-15VOUT |
| FIN0.75RD | FIREFLEX FIBERGLASS 3/4" RED 50' |
| ISL6613ACRZ-T | IC MOSFET DRVR SYNC BUCK 10-DFN |
| 76000724 | CABLE BARE WIRE 4' DB-9F |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3508 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Monolithic 1.4A Step-Down Switching Regulator |
| LT3508EFE#PBF | 功能描述:IC REG BUCK ADJ 1.4A DL 16TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LT3508EFE#TRPBF | 功能描述:IC REG BUCK ADJ 1.4A DL 16TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT3508EFEPBF | 制造商:Linear Technology 功能描述:Dual 1.4A Step-Down Regulator LT3508 |
| LT3508EFE-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Monolithic 1.4A Step-Down Switching Regulator |
发布紧急采购，3分钟左右您将得到回复。