- 您现在的位置：买卖IC网 > PDF目录13808 > LT3511MPMS#TRPBF (Linear Technology)IC REG FLYBK ISO ADJ .24A 16MSOP PDF资料下载
参数资料
| 型号： | LT3511MPMS#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 11/26页 |
| 文件大小： | 0K |
| 描述： | IC REG FLYBK ISO ADJ .24A 16MSOP |
| 标准包装： | 2,500 |
| 类型： | 回扫，隔离 |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 可调至 150V |
| 输入电压： | 4.5 V ~ 100 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 40kHz ~ 650kHz |
| 电流 - 输出： | 240mA |
| 同步整流器： | 无 |
| 工作温度： | -55°C ~ 150°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TFSOP（0.118"，3.00mm），12 引线 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 16-MSOP |
LT3511
APPLICATIONS INFORMATION
N <
t OFF(MIN) ? N PS ? ( V OUT + V F )
L PRI ≥
Turns Ratio
Note that when using an R FB /R REF resistor ratio to set
output voltage, the user has relative freedom in selecting
a transformer turns ratio to suit a given application. In
contrast, the use of simple ratios of small integers, e.g.,
1:1, 2:1, 3:2, provides more freedom in setting total turns
and mutual inductance.
Typically, choose the transformer turns to maximize avail-
able output power. For low output voltages (3.3V or 5V), a
N:1 turns ratio can be used with multiple primary windings
relative to the secondary to maximize the transformer’s
current gain (and output power). However, remember that
the SW pin sees a voltage that is equal to the maximum
input supply voltage plus the output voltage multiplied by
the turns ratio. In addition, leakage inductance will cause
a voltage spike (V LEAKAGE ) on top of this reflected voltage.
This total quantity needs to remain below the absolute
maximum rating of the SW pin to prevent breakdown of
the internal power switch. Together these conditions place
an upper limit on the turns ratio, N, for a given application.
Choose a turns ratio low enough to ensure:
150V – V IN(MAX) – V LEAKAGE
V OUT + V F
For larger N:1 values, choose a transformer with a larger
physical size to deliver additional current. In addition,
choose a large enough inductance value to ensure that
the off-time is long enough to measure the output voltage.
For lower output power levels, choose a 1:1 or 1:N trans-
former for the absolute smallest transformer size. A 1:N
transformer will minimize the magnetizing inductance
(and minimize size), but will also limit the available output
power. A higher 1:N turns ratio makes it possible to have
very high output voltages without exceeding the breakdown
voltage of the internal power switch.
The turns ratio is an important element in the isolated
feedback scheme. Make sure the transformer manufacturer
guarantees turns ratio accuracy within ±1%.
Saturation Current
The current in the transformer windings should not ex-
ceed its rated saturation current. Energy injected once the
core is saturated will not be transferred to the secondary
and will instead be dissipated in the core. Information on
saturation current should be provided by the transformer
manufacturers. Table 1 lists the saturation current of the
transformers designed for use with the LT3511.
Primary Inductance Requirements
The LT3511 obtains output voltage information from the
reflected output voltage on the switch pin. The conduction
of secondary winding current reflects the output voltage
on the primary. The sampling circuitry needs a minimum
of 400ns to settle and sample the reflected output voltage.
In order to ensure proper sampling, the secondary winding
needs to conduct current for a minimum of 400ns. The
following equation gives the minimum value for primary-
side magnetizing inductance:
L PRI ≥
I PEAK(MIN)
t OFF(MIN) = 400ns
I PEAK(MIN) = 55mA
In addition to the primary inductance requirement for
sampling time, the LT3511 has internal circuit constraints
that prevent the switch from staying on for less than 100ns.
If the inductor current exceeds the desired current limit
during that time, oscillation may occur at the output as
the current control loop will lose its ability to regulate.
The following equation, based on maximum input voltage,
must also be followed in selecting primary-side magnetiz-
ing inductance:
t ON(MIN) ? V IN(MAX)
I PEAK(MIN)
t ON(MIN) = 100ns
I PEAK(MIN) = 55mA
3511fc
11
相关PDF资料 |
PDF描述 |
|---|---|
| V72B3V3C100BG2 | CONVERTER MOD DC/DC 3.3V 100W |
| GMA15DTAD | CONN EDGECARD 30POS R/A .125 SLD |
| AS1330-BTDT-AD | IC REG BST SYNC ADJ 0.15A 8TDFN |
| MAX6721AUTZGD1+T | IC SUPERVISOR MPU SOT23-6 |
| V72B3V3C100BF | CONVERTER MOD DC/DC 3.3V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3512 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Monolithic High Voltage Isolated Flyback Converter |
| LT3512_11 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Monolithic High Voltage Isolated Flyback Converter |
| LT3512EMS#PBF | 功能描述:IC REG FLYBK ISO ADJ .42A 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LT3512EMS#TRPBF | 功能描述:IC REG FLYBK ISO ADJ .42A 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT3512EMSPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Monolithic High Voltage Isolated Flyback Converter |
发布紧急采购，3分钟左右您将得到回复。