参数资料
型号: LT3570EUF#TRPBF
厂商: LINEAR TECHNOLOGY CORP
元件分类: 稳压器
英文描述: 3.1 A SWITCHING REGULATOR, 2750 kHz SWITCHING FREQ-MAX, PQCC24
封装: 4 X 4 MM, LEAD FREE, PLASTIC, MO-220WGGD, QFN-24
文件页数: 9/20页
文件大小: 283K
代理商: LT3570EUF#TRPBF
LT3570
17
3570fb
will be enabled again going through a soft-start cycle.
Note: Overtemperature protection is intended to protect the
device during momentary overload conditions. Continuous
operation above the specied maximum operating junction
temperature may result in device degradation or failure.
PCB Layout
For proper operation and minimum EMI, care must be
taken during printed circuit board (PCB) layout. Figure 6
shows the high current paths in the step-down regulator
circuit. Note that in the step-down regulator, large switched
currents ow in the power switch, the catch diode and the
input capacitor.
Figure 7 shows the high current paths in the step-up
regulator. In the boost regulator, large switched currents
ow through the power switch, the switching diode, and
the output capacitor.
The loop formed by these large switched current com-
ponents should be as small as possible. Place these
components on the same side of the circuit board and
connect them on that layer. Place a local, unbroken ground
plane below these components and tie this ground plane
APPLICATIONS INFORMATION
Figure 6. Buck High Speed Switching Path
Figure 7. Boost High Speed Switching Path
to system ground at one location. Additionally, keep
the SW and BOOST nodes as small as possible. This is
implemented in the suggested layout of Figure 8 for the
QFN package which shows the topside metal from the
DC1106A demonstration board.
Thermal Considerations
To deliver the power that the LT3570 is capable of, it
is imperative that a good thermal path be provided to
dissipate the heat generated within the package. This can
be accomplished by taking advantage of the large ther-
mal pad on the underside of the IC. It is recommended
that multiple vias in the printed circuit board be used to
conduct heat away from the IC and into a copper plane
with as much area as possible.
Related Linear Technology Publications
Application notes 19, 35, 44, 76 and 88 contain more
detailed descriptions and design information for buck
regulators and other switching regulators. The LT1375 data
sheet has a more extensive discussion of output ripple,
loop compensation, and stability testing.
Figure 8. Suggested Layout
3570 F06
L2
D1 COUT
HIGH
FREQUENCY
CIRCULATING
PATH
CIN
LOAD
LT3570
3750 F07
L2
LT3570
D1
COUT
CIN
HIGH
FREQUENCY
SWITCHING
PATH
LOAD
相关PDF资料
PDF描述
LT3570EUF#PBF 3.1 A SWITCHING REGULATOR, 2750 kHz SWITCHING FREQ-MAX, PQCC24
LT3571IUD#PBF 0.57 A SWITCHING REGULATOR, 2300 kHz SWITCHING FREQ-MAX, PQCC16
LT3571EUD#PBF 0.57 A SWITCHING REGULATOR, 2300 kHz SWITCHING FREQ-MAX, PQCC16
LT3571EUD#TRPBF 0.57 A SWITCHING REGULATOR, 2300 kHz SWITCHING FREQ-MAX, PQCC16
LT3574EMS#PBF 1.1 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO16
相关代理商/技术参数
参数描述
LT3570FE 制造商:LINER 制造商全称:Linear Technology 功能描述:1.5A Buck Converter, 1.5A Boost Converter and LDO Controller
LT3570IFE#PBF 功能描述:IC REG BUCK/BST/LINEAR 20TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压(降压)同步(3),线性(LDO)(2) 功能:任何功能 输出数:5 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:5.6 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:*
LT3570IFE#TRPBF 功能描述:IC REG BUCK/BST/LINEAR 20TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压(降压)同步(3),线性(LDO)(2) 功能:任何功能 输出数:5 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:5.6 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:*
LT3570IFE-PBF 制造商:LINER 制造商全称:Linear Technology 功能描述:1.5A Buck Converter, 1.5A Boost Converter and LDO Controller
LT3570IFE-TRPBF 制造商:LINER 制造商全称:Linear Technology 功能描述:1.5A Buck Converter, 1.5A Boost Converter and LDO Controller