参数资料
型号: LT3573IMSE#TRPBF
厂商: Linear Technology
文件页数: 7/26页
文件大小: 0K
描述: IC REG FLYBACK ISO ADJ 16MSOP
标准包装: 2,500
类型: 回扫,隔离
输出类型: 可调式
输出数: 1
输出电压: 可调至 60V
输入电压: 3 V ~ 40 V
PWM 型: 电流模式,混合
频率 - 开关: 40kHz ~ 1MHz
电流 - 输出: 1.25A
同步整流器:
工作温度: -40°C ~ 125°C
安装类型: 表面贴装
封装/外壳: 16-TFSOP(0.118",3.00mm 宽)裸露焊盘
包装: 带卷 (TR)
供应商设备封装: 16-MSOP,裸露焊盘
配用: 732-3307-ND - BOARD EVAL FOR LT3573
相关产品: 732-2669-2-ND - TRANS FLYBACK LT3748 20UH SMD
732-2669-6-ND - TRANS FLYBACK LT3748 20UH SMD
732-2668-6-ND - TRANS FLYBACK LT3748 14UH SMD
732-2667-6-ND - TRANS FLYBACK LT3748 500UH SMD
732-2666-6-ND - TRANS FLYBACK LT3748 12UH SMD
732-2665-6-ND - TRANS FLYBACK LT3748 12UH SMD
732-2664-6-ND - TRANS FLYBACK LT3748 15UH SMD
732-2663-6-ND - TRANS FLYBACK LT3748 15UH SMD
732-2662-6-ND - TRANS FLYBACK LT3748 8UH SMD
732-2661-6-ND - TRANS FLYBACK LT3748 8UH SMD
更多...
LT3573
OPERATION
The LT3573 is a current mode switching regulator IC
designed specifically for the isolated flyback topology.
The special problem normally encountered in such cir-
cuits is that information relating to the output voltage on
the isolated secondary side of the transformer must be
communicated to the primary side in order to maintain
regulation. Historically, this has been done with opto-
isolators or extra transformer windings. Opto-isolator
circuits waste output power and the extra components
increase the cost and physical size of the power supply.
Opto-isolators can also exhibit trouble due to limited
dynamic response, nonlinearity, unit-to-unit variation
and aging over life. Circuits employing extra transformer
windings also exhibit deficiencies. Using an extra wind-
ing adds to the transformer’s physical size and cost, and
dynamic response is often mediocre.
The LT3573 derives its information about the isolated
output voltage by examining the primary-side flyback
pulse waveform. In this manner, no opto-isolator nor extra
transformer winding is required for regulation. The output
voltage is easily programmed with two resistors. Since this
IC operates in boundary control mode, the output voltage
is calculated from the switch pin when the secondary cur-
rent is almost zero. This method improves load regulation
without external resistors and capacitors.
The Block Diagram shows an overall view of the system.
Many of the blocks are similar to those found in traditional
switching regulators including: internal bias regulator,
oscillator, logic, current amplifier and comparator, driver,
and output switch. The novel sections include a special
flyback error amplifier and a temperature compensation
circuit. In addition, the logic system contains additional
logic for boundary mode operation, and the sampling
error amplifier.
The LT3573 features a boundary mode control method,
where the part operates at the boundary between continu-
ous conduction mode and discontinuous conduction mode.
The V C pin controls the current level just as it does in normal
current mode operation, but instead of turning the switch
on at the start of the oscillator period, the part detects
when the secondary side winding current is zero.
Boundary Mode Operation
Boundary mode is a variable frequency, current-mode
switching scheme. The switch turns on and the inductor
current increases until a V C pin controlled current limit. The
voltage on the SW pin rises to the output voltage divided
by the secondary-to-primary transformer turns ratio plus
the input voltage. When the secondary current through
the diode falls to zero, the SW pin voltage falls below V IN .
A discontinuous conduction mode (DCM) comparator
detects this event and turns the switch back on.
Boundary mode returns the secondary current to zero
every cycle, so the parasitic resistive voltage drops do not
cause load regulation errors. Boundary mode also allows
the use of a smaller transformer compared to continuous
conduction mode and no subharmonic oscillation.
At low output currents the LT3573 delays turning on the
switch, and thus operates in discontinuous mode. Unlike
a traditional flyback converter, the switch has to turn on
to update the output voltage information. Below 0.6V on
the V C pin, the current comparator level decreases to
its minimum value, and the internal oscillator frequency
decreases in frequency. With the decrease of the internal
oscillator, the part starts to operate in DCM. The output
current is able to decrease while still allowing a minimum
switch off-time for the error amp sampling circuitry. The
typical minimum internal oscillator frequency with V C
equal to 0V is 40kHz.
3573fd
For more information www.linear.com/LT3573
7
相关PDF资料
PDF描述
LT3574IMS#TRPBF IC REG FLYBK ISO ADJ .65A 16MSOP
LT3575IFE#TRPBF IC REG FLYBACK ISO ADJ 16TSSOP
LT3579EUFD-1#TRPBF IC REG MULTI CONFIG SYNC 20QFN
LT3580MPMS8E#TRPBF IC REG BOOST INV SEPIC 2A 8MSOP
LT3581IMSE#TRPBF IC REG MULTI CONFIG ADJ 16MSOP
相关代理商/技术参数
参数描述
LT3574 制造商:LINER 制造商全称:Linear Technology 功能描述:Isolated Flyback Converter Without an Opto-Coupler
LT3574EMS 制造商:LINER 制造商全称:Linear Technology 功能描述:Isolated Flyback Converter Without an Opto-Coupler
LT3574EMS#PBF 功能描述:IC REG FLYBK ISO ADJ .65A 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压(降压) 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON(1.45x1) 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2
LT3574EMS#TRPBF 功能描述:IC REG FLYBK ISO ADJ .65A 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压(降压) 输出类型:固定 输出数:1 输出电压:1.2V,1.5V,1.8V,2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP,10-MSOP(0.118",3.00mm 宽)裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘
LT3574EMSPBF 制造商:LINER 制造商全称:Linear Technology 功能描述:Isolated Flyback Converter Without an Opto-Coupler