- 您现在的位置：买卖IC网 > PDF目录80080 > LT3574EMS#TRPBF (LINEAR TECHNOLOGY CORP) 1.1 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO16 PDF资料下载
参数资料
| 型号： | LT3574EMS#TRPBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | 1.1 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封装： | LEAD FREE, PLASTIC, MSOP-16 |
| 文件页数： | 4/24页 |
| 文件大小： | 285K |
| 代理商： | LT3574EMS#TRPBF |
LT3574
3574f
applications inForMation
Turns Ratio
Note that when using an RFB/RREF resistor ratio to set
output voltage, the user has relative freedom in selecting
a transformer turns ratio to suit a given application. In
contrast, simpler ratios of small integers, e.g., 1:1, 2:1,
3:2, etc., can be employed to provide more freedom in
setting total turns and mutual inductance.
Typically,thetransformerturnsratioischosentomaximize
availableoutputpower.Forlowoutputvoltages(3.3Vor5V),
aN:1turnsratiocanbeusedwithmultipleprimarywindings
relative to the secondary to maximize the transformer’s
current gain (and output power). However, remember that
the SW pin sees a voltage that is equal to the maximum
input supply voltage plus the output voltage multiplied by
the turns ratio. This quantity needs to remain below the
abs max rating of the SW pin to prevent breakdown of the
internal power switch. Together these conditions place an
upper limit on the turns ratio, N, for a given application.
Choose a turns ratio low enough to ensure:
N
V V
V
IN MAX
OUT
F
<
+
50 –
(
)
For larger N:1 values, a transformer with a larger physical
size is needed to deliver additional current and provide a
largeenoughinductancevaluetoensurethattheoff-timeis
long enough to accurately measure the output voltage.
For lower output power levels, a 1:1 or 1:N transformer
can be chosen for the absolute smallest transformer size.
A 1:N transformer will minimize the magnetizing induc-
tance (and minimize size), but will also limit the available
output power. A higher 1:N turns ratio makes it possible
to have very high output voltages without exceeding the
breakdown voltage of the internal power switch.
Leakage Inductance
Transformer leakage inductance (on either the primary or
secondary) causes a voltage spike to appear at the primary
after the output switch turns off. This spike is increasingly
prominent at higher load currents where more stored
energy must be dissipated. In most cases, a snubber
circuit will be required to avoid overvoltage breakdown at
the output switch node. Transformer leakage inductance
should be minimized.
An RCD (resistor capacitor diode) clamp, shown in Fig-
ure 4, is required for most designs to prevent the leakage
inductance spike from exceeding the breakdown voltage
of the power device. The flyback waveform is depicted in
Figure 5. In most applications, there will be a very fast
voltage spike caused by a slow clamp diode that may not
exceed60V.Oncethediodeclamps,theleakageinductance
current is absorbed by the clamp capacitor. This period
should not last longer than 150ns so as not to interfere
with the output regulation, and the voltage during this
clamp period must not exceed 55V. The clamp diode turns
off after the leakage inductance energy is absorbed and
the switch voltage is then equal to:
VSW(MAX) = VIN(MAX) + N(VOUT + VF)
This voltage must not exceed 50V. This same equation
also determines the maximum turns ratio.
When choosing the snubber network diode, careful atten-
tion must be paid to maximum voltage seen by the SW
pin. Schottky diodes are typically the best choice to be
used in the snubber, but some PN diodes can be used if
they turn on fast enough to limit the leakage inductance
spike. The leakage spike must always be kept below 60V.
Figures 6 and 7 show the SW pin waveform for a 24VIN,
5VOUT application at a 0.5A load current. Notice that the
leakage spike is very high (more than 65V) with the bad
diode, while the good diode effectively limits the spike to
less than 55V.
相关PDF资料 |
PDF描述 |
|---|---|
| LTC6992IS6-4#PBF | SWITCHING CONTROLLER, PDSO6 |
| LTC694-3.3CN8 | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDIP8 |
| LM1575K-15/883 | 1.3 A SWITCHING REGULATOR, 52 kHz SWITCHING FREQ-MAX, MBFM2 |
| LX1570IM | 1 A SWITCHING CONTROLLER, 100 kHz SWITCHING FREQ-MAX, PDIP8 |
| LK4601-7ERD2TB1 | 1-OUTPUT 150 W AC-DC PWR FACTOR CORR MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3574IMS | 制造商:LINER 制造商全称:Linear Technology 功能描述:Isolated Flyback Converter Without an Opto-Coupler |
| LT3574IMS#PBF | 功能描述:IC REG FLYBK ISO ADJ .65A 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT3574IMS#TRPBF | 功能描述:IC REG FLYBK ISO ADJ .65A 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT3574IMSPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Isolated Flyback Converter Without an Opto-Coupler |
| LT3574IMSTRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Isolated Flyback Converter Without an Opto-Coupler |
发布紧急采购，3分钟左右您将得到回复。