- 您现在的位置：买卖IC网 > PDF目录14028 > LT3574EMS#TRPBF (Linear Technology)IC REG FLYBK ISO ADJ .65A 16MSOP PDF资料下载
参数资料
| 型号： | LT3574EMS#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 9/24页 |
| 文件大小： | 0K |
| 描述： | IC REG FLYBK ISO ADJ .65A 16MSOP |
| 标准包装： | 2,500 |
| 类型： | 回扫，隔离 |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 可调至 60V |
| 输入电压： | 3 V ~ 40 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 40kHz ~ 1MHz |
| 电流 - 输出： | 650mA |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TFSOP（0.118"，3.00mm 宽） |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 16-MSOP |
| 相关产品： | 732-2669-2-ND - TRANS FLYBACK LT3748 20UH SMD 732-2669-6-ND - TRANS FLYBACK LT3748 20UH SMD 732-2668-6-ND - TRANS FLYBACK LT3748 14UH SMD 732-2667-6-ND - TRANS FLYBACK LT3748 500UH SMD 732-2666-6-ND - TRANS FLYBACK LT3748 12UH SMD 732-2665-6-ND - TRANS FLYBACK LT3748 12UH SMD 732-2664-6-ND - TRANS FLYBACK LT3748 15UH SMD 732-2663-6-ND - TRANS FLYBACK LT3748 15UH SMD 732-2662-6-ND - TRANS FLYBACK LT3748 8UH SMD 732-2661-6-ND - TRANS FLYBACK LT3748 8UH SMD 更多... |
LT3574
APPLICATIONS INFORMATION
L PRI ≥ V OUT ?
? N PS = V OUT ? N PS ? ?
R REF ? N PS ?? ( V OUT + V F ) A + V TC ??
R FB =
ERRORAMPLIFIER—DYNAMICTHEORY
Due to the sampling nature of the feedback loop, there
are several timing signals and other constraints that are
required for proper LT3574 operation.
Minimum Current Limit
The LT3574 obtains output voltage information from the
SW pin when the secondary winding conducts current.
The sampling circuitry needs a minimum amount of time
to sample the output voltage. To guarantee enough time,
a minimum inductance value must be maintained. The
primary side magnetizing inductance must be chosen
above the following value:
t MIN ? 2 μH ?
?
I MIN ? V ?
t MIN = minimum off-time, 350ns
I MIN = minimum current limit, 175mA
The minimum current limit is higher than that on the Elec-
trical Characteristics table due to the overshoot caused by
the comparator delay.
Leakage Inductance Blanking
When the output switch first turns off, the flyback pulse
appears. However, it takes a finite time until the transformer
primary-side voltage waveform approximately represents
the output voltage. This is partly due to the rise time on
the SW node, but more importantly due to the trans-
former leakage inductance. The latter causes a very fast
voltage spike on the primary side of the transformer that
is not directly related to output voltage (some time is also
required for internal settling of the feedback amplifier
circuitry). The leakage inductance spike is largest when
the power switch current is highest.
In order to maintain immunity to these phenomena, a fixed
delay is introduced between the switch turn-off command
and the beginning of the sampling. The blanking is internally
set to 150ns. In certain cases, the leakage inductance may
not be settled by the end of the blanking period, but will
not significantly affect output regulation.
Selecting R FB and R REF Resistor Values
The expression for V OUT, developed in the Operation sec-
tion, can be rearranged to yield the following expression
for R FB :
V BG
where,
V OUT = Output voltage
V F = Switching diode forward voltage
A = Ratio of Q1, IC to IE, typically 0.986
N PS = Effective primary-to-secondary turns ratio
V TC = 0.55V
The equation assumes the temperature coefficients of
the diode and V TC are equal, which is a good first-order
approximation.
Strictly speaking, the above equation defines R FB not as an
absolute value, but as a ratio of R REF . So, the next ques-
tion is, “What is the proper value for R REF ?” The answer
is that R REF should be approximately 6.04k. The LT3574
is trimmed and specified using this value of R REF . If the
impedance of R REF varies considerably from 6.04k, ad-
ditional errors will result. However, a variation in R REF of
several percent is acceptable. This yields a bit of freedom
in selecting standard 1% resistor values to yield nominal
R FB /R REF ratios. The R FB resistor given by this equation
should also be verified experimentally, and adjusted if
necessary for best output accuracy.
Tables 1-4 are useful for selecting the resistor values for
R REF and R FB with no equations. The tables provide R FB ,
R REF and R TC values for common output voltages and
common winding ratios.
Table 1. Common Resistor Values for 1:1 Transformers
V OUT (V) N PS R FB (kΩ) R REF (kΩ) R TC (kΩ)
3.3 1.00 18.7 6.04 19.1
5 1.00 27.4 6.04 28
12 1.00 64.9 6.04 66.5
15 1.00 80.6 6.04 80.6
20 1.00 107 6.04 105
3574f
相关PDF资料 |
PDF描述 |
|---|---|
| TFL0816-18N | INDUCTOR 18NH +/-2% 0603 |
| HM79S-125331LFTR13 | SHIELDED DRUM INDUCTORS |
| GBC50DCAH-S189 | CONN EDGECARD 100PS R/A .100 SLD |
| LT3573EMSE#TRPBF | IC REG FLYBACK ISO ADJ 16MSOP |
| RSC15DRYN-S13 | CONN EDGECARD 30POS .100 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3574IMS | 制造商:LINER 制造商全称:Linear Technology 功能描述:Isolated Flyback Converter Without an Opto-Coupler |
| LT3574IMS#PBF | 功能描述:IC REG FLYBK ISO ADJ .65A 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT3574IMS#TRPBF | 功能描述:IC REG FLYBK ISO ADJ .65A 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT3574IMSPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Isolated Flyback Converter Without an Opto-Coupler |
| LT3574IMSTRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Isolated Flyback Converter Without an Opto-Coupler |
发布紧急采购，3分钟左右您将得到回复。