- 您现在的位置：买卖IC网 > PDF目录1825 > LT3579EUFD-1#TRPBF (Linear Technology)IC REG MULTI CONFIG SYNC 20QFN PDF资料下载
参数资料
| 型号： | LT3579EUFD-1#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 11/40页 |
| 文件大小： | 0K |
| 描述： | IC REG MULTI CONFIG SYNC 20QFN |
| 标准包装： | 2,500 |
| 类型： | 升压（升压），反相，回扫，Sepic |
| 输出数： | 1 |
| 输入电压： | 2.5 V ~ 16 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 200kHz ~ 2.5MHz |
| 电流 - 输出： | 6A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-WFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 20-QFN 裸露焊盘（5x4） |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
LT3579/LT3579-1
OPERATION
Sample Mode
Sample Mode is the mechanism used by the LT3579 to
aid in the detection of output shorts. It refers to a state of
the LT3579 where the master and slave power switches
(Q1 and Q2) are turned on for a minimum period of time
every clock cycle (or every few clock cycles in frequency
foldback) in order to “sample” the inductor current. If the
sampled current through Q1 exceeds the master switch
current limit of 3.4A (minimum), the LT3579 triggers an
overcurrent fault internally (see Operation-Fault section for
details). Sample Mode exists when FB is out of regulation
by more than 3.7% or 45mV < FB < 1.17V (typical). The
LT3579’s power switches are designed to handle a total
peak current of 6A (minimum).
Frequency Foldback
The frequency foldback circuit reduces the switching
frequency when 350mV < FB < 900mV (typical). This
feature lowers the minimum duty cycle that the part can
achieve, thus allowing better control of the inductor current
during start-up. When the FB voltage is pulled outside of
this range, the switching frequency returns to normal.
Note that the peak inductor current at start-up is a
function of many variables including load profile, output
capacitance, target V OUT , V IN , switching frequency, etc. Test
the application’s performance at start-up to ensure that
the peak inductor current does not exceed the minimum
current limit.
OPERATION – REGULATION
The following description of the LT3579’s operation
assumes the FB voltage is close enough to its regulation
target so that the part is not in Sample Mode. Use the
Block Diagram as a reference when stepping through
the following description of the LT3579 operating in
regulation. At the start of each oscillator cycle, the SR
latch (SR1) is set, which turns on the power switches Q1
and Q2. The collector current through the master switch,
Q1, is ~1.3 times the collector current through the slave
switch, Q2, when the collectors of the two switches are
tied together. Q1’s emitter current flows through a current
sense resistor (R S ) generating a voltage proportional to
the total switch current. This voltage (amplified by A4) is
added to a stabilizing ramp and the resulting sum is fed
into the positive terminal of the PWM comparator A3.
When the voltage on the positive input of A3 exceeds
the voltage on the negative input, the SR latch is reset,
turning off the master and slave power switches. The
voltage on the negative input of A3 (V C pin) is set by A1
(or A2), which is simply an amplified difference between
the FB pin voltage and the reference voltage (1.215V if
the LT3579 is configured as a boost converter, or 9mV
if configured as an inverting converter). In this manner,
the error amplifer sets the correct peak current level to
maintain output regulation.
As long as the part is not in fault (see Operation – FAULT
section) and the SS pin exceeds 1.8V, the LT3579 drives its
CLKOUT pin at the frequency set by the RT pin or the SYNC
pin. The CLKOUT pin can synchronize other compatible
switching regulator ICs (including additional LT3579s) with
the LT3579. Additionally, the duty cycle of CLKOUT varies
linearly with the part’s junction temperature and may be
used as a temperature monitor. The CLKOUT signal on the
LT3579-1 is ~180° out of phase with the internal oscillator
and has a fixed duty cycle of ~50%.
OPERATION – FAULT
The LT3579’s FAULT pin is an active low, bidirectional
pin (refer to Block Diagram) that pulls low to indicate a
fault. Each of the following events can trigger a fault in
the LT3579:
A. FAULT1 Events:
1. SW Overcurrent
a. I SW1 > 3.4A (minimum)
b. (I SW1 + I SW2 ) > 6A (minimum)
2. V IN Voltage > 16.2V (minimum)
3. SW1 Voltage and/or SW2 Voltage > 42V
(minimum)
4. Die Temperature > 165°C
B. FAULT2 Events:
1. Pulling the FAULT pin low externally
35791f
11
相关PDF资料 |
PDF描述 |
|---|---|
| LT3580MPMS8E#TRPBF | IC REG BOOST INV SEPIC 2A 8MSOP |
| LT3581IMSE#TRPBF | IC REG MULTI CONFIG ADJ 16MSOP |
| LT3582EUD-5#TRPBF | IC REG BOOST INV +/-5V DL 16QFN |
| LT3587EUD#TRPBF | IC REG BOOST INV ADJ DL 20QFN |
| LT3640IFE#TRPBF | IC REG BUCK FIX/ADJ DL 28TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3579EUFD-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:6A Boost/Inverting DC/DC Converter with Fault Protection |
| LT3579EUFD-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:6A Boost/Inverting DC/DC Converter with Fault Protection |
| LT3579IFE#PBF | 功能描述:IC REG MULTI CONFIG SYNC 20TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT3579IFE#TRPBF | 功能描述:IC REG MULTI CONFIG SYNC 20TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT3579IFE-1#PBF | 功能描述:IC REG MULTI CONFIG SYNC 20TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
发布紧急采购，3分钟左右您将得到回复。