- 您现在的位置：买卖IC网 > PDF目录14836 > LT3582EUD#PBF (Linear Technology)IC REG BOOST INV ADJ DL 16QFN PDF资料下载
参数资料
| 型号： | LT3582EUD#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 8/28页 |
| 文件大小： | 0K |
| 描述： | IC REG BOOST INV ADJ DL 16QFN |
| 特色产品： | LT3582 I2C DC/DC Converters |
| 标准包装： | 121 |
| 类型： | 升压（升压），反相 |
| 输出类型： | 可调式 |
| 输出数： | 2 |
| 输出电压： | 3.2 V ~ 12.78 V，-1.2 V ~ -13.95 V |
| 输入电压： | 2.55 V ~ 5.5 V |
| PWM 型： | 混合物 |
| 电流 - 输出： | 350mA，600mA |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-WFQFN 裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 16-QFN-EP（3x3） |
| 产品目录页面： | 1332 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LT3582/LT3582-5/LT3582-12
PIN FUNCTIONS
CA (Pin 1): I 2 C Address Select Pin. Tie this pin to V IN to set
the 7-bit address to 0110 001. Tie to GND for 1000 101.
V OUTN (Pin 2): Negative Output Voltage Pin. When the con-
verter is operating, this pin is regulated to the programmed
negative output voltage. Place a ceramic capacitor from
this pin to GND.
SWN (Pins 3, 4): Negative Switching Node for the In-
verting Converter. This is the drain of the internal PMOS
power switch. Connect one end of the Inverting inductor
to these pins. Keep the trace area on these pins as small
as possible.
V IN (Pin 5): Input Supply Pin and Source of the PMOS
Power Switch. This pin must be bypassed locally with a
ceramic capacitor. The operating voltage range of this pin
is 2.55V to 5.5V.
RAMPN (Pin 6): Soft-Start Ramp Pin for the Inverting
Converter. Place a capacitor from this pin to GND. A
programmable current of 1μA to 8μA (LT3582) or 1μA
(LT3582-5/LT3582-12) charges this pin during start-up,
limiting the ramp rate of V OUTN . This pin is discharged to
GND during shutdown.
RAMPP (Pin 7): Soft-Start Ramp Pin for the Boost Convert-
er. Place a capacitor from this pin to GND. A programmable
current of 1μA to 8μA (LT3582) or 1μA (LT3582-5/LT3582-12)
charges this pin during start-up, limiting the ramp rate of
V OUTP . This pin is discharged to GND in shutdown.
SHDN (Pin 8): Shutdown Pin. Drive this pin to 1.1V or
higher to enable the part. Drive to 0.3V or lower to shut
down. Includes an integrated 222k pull-down resistor.
CAPP (Pins 10, 11): Connect the Boost output capacitor
from these pins to GND. During shutdown, the voltage on
these pins will remain close to the input voltage due to
the path through the Boost inductor and Schottky. During
normal operation, CAPP will be boosted slightly higher
than the programmed output voltage.
SWP (Pin 12): Positive Switching Node for the Boost
Converter. This is the drain of the internal NMOS power
switch. Connect one end of the Boost inductor to this pin.
Keep the trace area on this pin as small as possible.
GND (Pin 13): Ground Pin. Tie to a local ground plane.
Proper PCB layout is required to achieve advertised per-
formance; see the Applications Information section for
more information.
V PP (Pin 14): Programming Voltage Pin. Drive this pin
to 13-15V when programming the OTP memory. Float
otherwise. A bypass capacitor should be placed from this
node to GND if V PP is used for programming. If V PP falls
below 13V during OTP programming, an internal FAULT
bit, which can be read through the I 2 C interface, can be
set high.
SDA (Pin 15): I 2 C Bidirectional Data Pin. Tie to GND or
V IN if unused.
SCL (Pin 16): I 2 C Clock Pin. Tie to GND or V IN if un-
used.
Exposed Pad (Pin 17): Ground Pin. Tie to a local ground
plane. Proper PCB layout is required to achieve advertised
performance; see the Applications Information section for
more information.
V OUTP (Pin 9): Output of the Boost Converter Output
Disconnect Circuit. A ceramic capacitor should be placed
from this node to GND. During shutdown, this pin is
disconnected from the Boost network which allows this
pin to discharge to GND, assuming a load is present to
discharge the capacitance.
3582512fb
8
相关PDF资料 |
PDF描述 |
|---|---|
| RBA36DTMD | CONN EDGECARD 72POS R/A .125 SLD |
| MAX6463UR49+T | IC VOLT DETECTOR LP SOT23-3 |
| RBA36DTBN | CONN EDGECARD 72POS R/A .125 SLD |
| MAX6463XR54+T | IC VOLT DETECTOR LP SC70-3 |
| EBM40DRSD | CONN EDGECARD 80POS DIP .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3582EUDTRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:I2C Programmable Boost and Single Inductor Inverting DC/DC Converters with OTP |
| LT3585-0 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Photofl ash Chargers with Adjustable Input Current and IGBT Drivers |
| LT3585EDDB-0 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Photofl ash Chargers with Adjustable Input Current and IGBT Drivers |
| LT3585EDDB-0#TRPBF | 功能描述:IC CHARGER PHOTOFLASH 10-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 标准包装:1 系列:- 应用:手持/移动设备 电流 - 电源:- 电源电压:3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-LLP-EP（4x4） 包装:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名称:LP3905SD-30DKR |
| LT3585EDDB-1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Photofl ash Chargers with Adjustable Input Current and IGBT Drivers |
发布紧急采购，3分钟左右您将得到回复。