- 您现在的位置：买卖IC网 > PDF目录20896 > LT3593ES6#TRPBF (Linear Technology)IC LED DRIVR WHITE BCKLGT TSOT-6 PDF资料下载
参数资料
| 型号： | LT3593ES6#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 7/16页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVR WHITE BCKLGT TSOT-6 |
| 标准包装： | 2,500 |
| 拓扑： | 升压（升压） |
| 输出数： | 1 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光 |
| 类型 - 次要： | 白色 LED |
| 频率： | 850kHz ~ 1.15MHz |
| 电源电压： | 2.7 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-6 细型，TSOT-23-6 |
| 供应商设备封装： | TSOT-23-5 |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 85°C |
LT3593
OPERATION
The LT3593 uses a constant frequency, current mode
control boost scheme to provide excellent line and load
regulation. Operation can be best understood by referring
to the Block Diagram in Figure 1.
Output Disconnect
An internal switch connects between the CAP pin and the
LED pin. The top of the LED string is connected to the
LED pin. The string can be terminated to ground or to
V IN if a low number of LEDs are driven. When the part is
in shutdown, the switch is off; allowing no current to run
through the LEDs.
Current Programming
The LED current can be set to 32 different values
(625μA – 20mA) by strobing the CTRL pin. A 5-bit
counter is decremented by 1 on a CTRL pin rising edge,
reducing the programmed current by 625μA each time.
CTRL
CTRL
CTRL
CTRL
The desired current can be calculated by:
I LED = 20mA – (N – 1) ? 625μA
where N is the number of rising edges. When the desired
current setting is reached, the CTRL pin must stay high.
128μs after the last rising edge on the CTRL pin, the
regulator will enable the output and start to regulate the
LED current to the programmed value. Figure 2 shows
an example of how the part can be programmed.
If a different current is desired, the CTRL pin can be strobed
again. The ?rst falling edge will reset the internal register
to the 20mA setting. While the new current is being pro-
grammed, the device will continue to regulate the previously
programmed value until the CTRL pin has remained high
for at least 128μs, at which time the regulated current will
slew to the newly programmed value. Figure 3 shows how
to program a new LED current level.
If the CTRL pin is held low for longer than 128μs, the part
will go into the shutdown mode.
FULL CURRENT
20mA
17.5mA
15mA
12.5mA
3593 F02
Figure 2. Current Programming
CTRL
128μs
128μs
128μs
20mA
20mA
17.5mA
17.5mA
LED
CURRENT
Figure 3. Current Programming and Shutdown Timing
SHDN
3593 F03
3593f
7
相关PDF资料 |
PDF描述 |
|---|---|
| P51-100-A-AF-MD-4.5OVP-000-000 | SENSOR 100PSI 9/16-18 UNF 4.5V |
| 4929-1/2"X72YD BULK SM PK | TAPE VHB ACRYLIC FOAM 1/2"X 72YD |
| LT3593EDC#TRPBF | IC LED DRIVER WHITE BCKLGT 6-DFN |
| LT3593EDC#TRMPBF | IC LED DRIVER WHITE BCKLGT 6-DFN |
| REC7.5-2409SRW/H3/A/M/CTRL | CONV DC/DC 7.5W 18-36VIN 09VOUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3595 | 制造商:LINER 制造商全称:Linear Technology 功能描述:16 Channel Buck Mode LED Driver |
| LT3595A | 制造商:LINER 制造商全称:Linear Technology 功能描述:16 Channel Buck Mode LED Driver |
| LT3595AEUHH#PBF | 功能描述:IC LED DRIVR WHITE BCKLGT 56-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
| LT3595AEUHH#TRPBF | 功能描述:IC LED DRIVR WHITE BCKLGT 56-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
| LT3595AEUHHPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:16 Channel Buck Mode LED Driver |
发布紧急采购，3分钟左右您将得到回复。