- 您现在的位置：买卖IC网 > PDF目录16002 > LT3650IDD-8.2#PBF (Linear Technology)IC CHARGER LI-ION 8.2V 2A 12-DFN PDF资料下载
参数资料
| 型号： | LT3650IDD-8.2#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 10/22页 |
| 文件大小： | 0K |
| 描述： | IC CHARGER LI-ION 8.2V 2A 12-DFN |
| 标准包装： | 121 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion）、锂聚合物（Li-Pol） |
| 电源电压： | 9 V ~ 32 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 12-WFDFN 裸露焊盘 |
| 供应商设备封装： | 12-DFN |
| 包装： | 管件 |
LT3650-8.2/LT3650-8.4
OPERATION
The I TH error voltage corresponds linearly to average cur-
rent sensed across the inductor current sense resistor,
allowing maximum charge current control by limiting the
effective voltage range of I TH . A clamp limits this voltage
to 1V which, in turn, limits the current sense voltage to
100mV. This sets the maximum charge current, or the
current delivered while the charger is operating in constant-
current (CC) mode, which corresponds to 100mV across
R SENSE . This maximum charge current level can also be
manipulated through the RNG/SS pin (see the RNG/SS:
Dynamic Charge Current Adjust and RNG/SS: Soft-Start
sections).
If the voltage on the BAT pin is below V BAT(PRE) , the LT3650
engages precondition mode. During the precondition inter-
val, the charger continues to operate in constant-current
mode, but the maximum charge current is reduced to 15%
of the maximum programmed value as set by R SENSE .
When the charger output voltage on the BAT pin approaches
the float voltage (V BAT(FLT) ), the charger transitions into
constant-voltage (CV) mode, and charge current is reduced
from the maximum value. As this occurs, the I TH voltage
falls from the limit clamp and servos to lower voltages.
The IC monitors the I TH voltage as it is reduced, and
detection of the C/10 charge current is achieved when
I TH = 0.1V. If the charger is configured for C/10 termina-
tion, this threshold is used to terminate the charge cycle.
Once the charge cycle is terminated, the CHRG status
pin becomes high impedance and the charger enters low
current standby mode.
The LT3650 contains an internal charge cycle timer that
terminates a successful charge cycle after a programmed
amount of time. This timer is typically programmed to
achieve end-of-cycle (EOC) in three hours, but can be
configured for any amount of time by setting an appropriate
timing capacitor value (C TIMER ). When timer termination
is used, the charge cycle does not terminate after C/10
is achieved. Because the CHRG status pin responds to
the C/10 current level, the IC will indicate a fully charged
battery status, but the charger will continue to source
low currents into the battery until the programmed EOC
time has elapsed, at which time the charge cycle will
terminate. At EOC, when the charging cycle terminates, if
the battery did not achieve at least 97.5% of the full float
voltage, charging is deemed unsuccessful. The LT3650
will then re-initiate, and charging will continue for another
full timer cycle.
Use of the timer function also enables bad-battery detec-
tion. This fault condition is achieved if the battery does
not respond to preconditioning and the charger remains
in (or enters) precondition mode after one-eighth of the
programmed charge cycle time. A bad-battery fault halts
the charging cycle, the CHRG status pin goes high imped-
ance, and the FAULT pin is pulled low.
When the LT3650 terminates a charging cycle, whether
through C/10 detection or by reaching timer EOC, the
average current mode analog loop remains active but
the internal float voltage reference is reduced by 2.5%.
Because the voltage on a successfully charged battery is
at the full float voltage, the voltage error amp detects an
overvoltage condition and rails low. When the voltage er-
ror amp output drops below 0.3V, the IC enters standby
mode, where most of the internal circuitry is disabled, and
the V IN bias current is reduced to 85μA. When the voltage
on the BAT pin drops below the reduced float reference
level, the output of the voltage error amp will climb, at
which point the IC comes out of standby mode and a new
charging cycle is initiated.
36508284fd
10
相关PDF资料 |
PDF描述 |
|---|---|
| CCP1.25BK50 | CLEAN CUT 1 1/4" BLACK 50' |
| M3BEK-5006R | IDC CABLE - MSR50K/MC50M/MCE50K |
| CCP0.13BK100 | CLEAN CUT 1/8" BLACK 100' |
| VI-JVN-EZ-F2 | CONVERTER MOD DC/DC 18.5V 25W |
| 35PK2200MEFC16X25 | CAP ALUM 2200UF 35V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3650IMSE-4.1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Voltage 2 Amp Monolithic Li-Ion Battery Charger |
| LT3650IMSE-4.1#PBF | 功能描述:IC CHARGER LI-ION 4.1V 2A 12MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LT3650IMSE-4.1#TRPBF | 功能描述:IC CHARGER LI-ION 4.1V 2A 12MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LT3650IMSE-4.1PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Voltage 2 Amp Monolithic Li-Ion Battery Charger |
| LT3650IMSE-4.1TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Voltage 2 Amp Monolithic Li-Ion Battery Charger |
发布紧急采购，3分钟左右您将得到回复。