- 您现在的位置：买卖IC网 > PDF目录14802 > LT3680EDD#PBF (Linear Technology)IC REG BUCK ADJ 3.5A 10DFN PDF资料下载
参数资料
| 型号： | LT3680EDD#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 10/24页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 3.5A 10DFN |
| 标准包装： | 121 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.79 V ~ 30 V |
| 输入电压： | 3.6 V ~ 36 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 230kHz ~ 2.45MHz |
| 电流 - 输出： | 3.5A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-WFDFN 裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 10-DFN（3x3） |
| 产品目录页面： | 1332 (CN2011-ZH PDF) |
LT3680
APPLICATIONS INFORMATION
L = ? OUT D ? ? 1– OUT D ?
operating input voltage. Conversely, a lower switching
frequency will be necessary to achieve safe operation at
high input voltages.
If the output is in regulation and no short-circuit, start-
up, or overload events are expected, then input voltage
transients of up to 36V are acceptable regardless of the
switching frequency. In this mode, the LT3680 may enter
pulse skipping operation where some switching pulses
are skipped to maintain output regulation. In this mode
the output voltage ripple and inductor current ripple will
be higher than in normal operation.
The minimum input voltage is determined by either the
LT3680’s minimum operating voltage of ~3.6V or by its
maximum duty cycle (see equation in previous section).
The minimum input voltage due to duty cycle is:
ripple current. The LT3680’s switch current limit (I LIM ) is
5.5A at low duty cycles and decreases linearly to 4.5A at
DC = 0.8. The maximum output current is a function of
the inductor ripple current:
I OUT(MAX) = I LIM – Δ I L /2
Be sure to pick an inductor ripple current that provides
suf?cient maximum output current (I OUT(MAX) ).
The largest inductor ripple current occurs at the highest
V IN . To guarantee that the ripple current stays below the
speci?ed maximum, the inductor value should be chosen
according to the following equation:
? V + V ? ? V + V ?
? f SW Δ I L ? ? V IN ( MAX ) ?
V IN ( MIN ) =
V OUT + V D
1– f SW t OFF ( MIN )
– V D + V SW
where V D is the voltage drop of the catch diode (~0.4V),
V IN(MAX) is the maximum input voltage, V OUT is the output
voltage, f SW is the switching frequency (set by R T ), and L
where V IN(MIN) is the minimum input voltage, and t OFF(MIN)
is the minimum switch off time (150ns). Note that higher
switching frequency will increase the minimum input
voltage. If a lower dropout voltage is desired, a lower
switching frequency should be used.
Inductor Selection
For a given input and output voltage, the inductor value
and switching frequency will determine the ripple current.
The ripple current Δ I L increases with higher V IN or V OUT
and decreases with higher inductance and faster switching
is in the inductor value.
The inductor’s RMS current rating must be greater than the
maximum load current and its saturation current should be
about 30% higher. For robust operation in fault conditions
(start-up or short circuit) and high input voltage (>30V),
the saturation current should be above 5A. To keep the
ef?ciency high, the series resistance (DCR) should be less
than 0.1 , and the core material should be intended for
high frequency applications. Table 1 lists several vendors
and suitable types.
Table 1. Inductor Vendors
frequency. A reasonable starting point for selecting the
ripple current is:
Δ I L = 0.4(I OUT(MAX) )
where I OUT(MAX) is the maximum output load current. To
guarantee suf?cient output current, peak inductor current
must be lower than the LT3680’s switch current limit (I LIM ).
The peak inductor current is:
I L(PEAK) = I OUT(MAX) + Δ I L /2
VENDOR
Murata
TDK
Toko
Sumida
NEC
URL
www.murata.com
www.componenttdk.com
www.toko.com
www.sumida.com
www.nec.com
PART SERIES
LQH55D
SLF10145
D75C
D75F
CDRH74
CR75
CDRH8D43
MPLC073
MPBI0755
TYPE
Open
Shielded
Shielded
Open
Shielded
Open
Shielded
Shielded
Shielded
where I L(PEAK) is the peak inductor current, I OUT(MAX) is
the maximum output load current, and Δ I L is the inductor
3680fb
10
相关PDF资料 |
PDF描述 |
|---|---|
| GCB40DHND | CONN EDGECARD 80POS .050 DIP SLD |
| RCC40DRYH | CONN EDGECARD 80POS DIP .100 SLD |
| V110C24T100BF2 | CONVERTER MOD DC/DC 24V 100W |
| RCC40DRXS | CONN EDGECARD 80POS DIP .100 SLD |
| CDR125NP-681MC | POWER INDUCTOR 680UH 0.40A SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3680EDD-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:36V, 3.5A, 2.4MHz Step-Down Switching Regulator with 75μA Quiescent Current |
| LT3680EMSE#PBF | 功能描述:IC REG BUCK ADJ 3.5A 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LT3680EMSE#TRPBF | 功能描述:IC REG BUCK ADJ 3.5A 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT3680EMSEPBF | 制造商:Linear Technology 功能描述:3.5A, 2.4MHz Step Down Regulator LT3680 |
| LT3680EMSE-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:36V, 3.5A, 2.4MHz Step-Down Switching Regulator with 75μA Quiescent Current |
发布紧急采购，3分钟左右您将得到回复。