- 您现在的位置：买卖IC网 > PDF目录14819 > LT3682EDD#PBF (Linear Technology)IC REG BUCK ADJ 1A 12DFN PDF资料下载
参数资料
| 型号： | LT3682EDD#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 21/24页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 1A 12DFN |
| 标准包装： | 121 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.8 V ~ 20 V |
| 输入电压： | 3.6 V ~ 36 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 250kHz ~ 2.2MHz |
| 电流 - 输出： | 1A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 12-WFDFN 裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 12-DFN |
| 产品目录页面： | 1332 (CN2011-ZH PDF) |
LT3682
APPLICATIONS INFORMATION
PCB Layout
For proper operation and minimum EMI, care must be taken
during printed circuit board layout. Figure 10 shows the
recommended component placement with trace, ground
plane and via locations. Note that large, switched currents
?ow in the LT3682’s V IN , SW and PGND pins, the catch
diode and the input capacitor (C IN ). The loop formed by
these components should be as small as possible. These
components, along with the inductor and output capacitor
(C OUT ), should be placed on the same side of the circuit
board, and their connections should be made on that layer.
All connections to GND should be made at a common
star ground point or directly to a local, unbroken ground
plane below these components. The SW and BOOST nodes
GND
C2
VOUT
C1
D1
L
should be laid out carefully to avoid interference. If the
VIN
GND
part is synchronized externally using the SYNC pin, care
must be taken laying out this signal to avoid interference
with sensitive nodes, especially V C , FB, and R T . Finally,
keep the FB, R T , and V C nodes small so that the ground
traces will shield them from the SW and BOOST nodes.
The exposed pad Pin 13 on the bottom of the package
acts as a heat sink and must be soldered to the ground
node. To keep thermal resistance low, extend the ground
plane as much as possible and add thermal vias under and
near the LT3682 to any additional ground planes within
the circuit board and on the bottom side. Keep in mind
that the thermal design must keep the junctions of the
IC below the speci?ed absolute maximum temperature
of 125°C.
High Temperature Considerations
The PCB must provide heat sinking to keep the LT3682
cool. The exposed pad on the bottom of the package must
be soldered to a copper area, which in turn should be
tied to large copper layers below with thermal vias; these
layers will spread the heat dissipated by the LT3682. Place
additional vias to reduce thermal resistance further. With
these steps, the thermal resistance from die (or junction)
to ambient can be reduced to θ JA = 35°C/W or less. With
100 LFPM air?ow, this resistance can fall by another 25%.
Further increases in air?ow will lead to lower thermal
3682 F10
Figure 10. A Good PCB Layout Ensures Proper, Low EMI Operation
the LT3682, it is possible to dissipate enough heat to raise
the junction temperature beyond the absolute maximum of
125°C. When operating at high ambient temperatures, the
maximum load current should be derated as the ambient
temperature approaches these maximums. If the junction
temperature reaches the thermal shutdown threshold, the
part will stop switching to prevent internal damage due
to overheating.
Power dissipation within the LT3682 can be estimated
by calculating the total power loss from an ef?ciency
measurement. The die temperature is calculated by
multiplying the LT3682 power dissipation by the thermal
resistance from junction to ambient.
Other Linear Technology Publications
Application Notes 19, 35 and 44 contain more detailed
descriptions and design information for buck regulators
and other switching regulators. The LT1376 data sheet
has a more extensive discussion of output ripple, loop
compensation and stability testing. Design Note 318
shows how to generate a bipolar output supply using a
buck regulator.
resistance. Because of the large output current capability of
3682f
21
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3388EMSE-3#PBF | IC REG BUCK SYNC 50MA 10MSOP |
| LTC3631EMS8E#PBF | IC REG BUCK SYNC ADJ 0.1A 8MSOP |
| VI-JVM-EY-F4 | CONVERTER MOD DC/DC 10V 50W |
| LTC3388EDD-1#PBF | IC REG BUCK SYNC 50MA 10DFN |
| VI-JVM-EY-F3 | CONVERTER MOD DC/DC 10V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3682EDD-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:1A Micropower Step-Down |
| LT3682IDD#PBF | 功能描述:IC REG BUCK ADJ 1A 12DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:MIC23xxx HyperLight Load™ Regulators 标准包装:5,000 系列:HyperLight Load® 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.8V 输入电压:2.7 V ~ 5.5 V PWM 型:混合物 频率 - 开关:4MHz 电流 - 输出:2A 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘，8-MLF? 包装:带卷 (TR) 供应商设备封装:8-MLF?（2x2） 产品目录页面:1094 (CN2011-ZH PDF) 其它名称:576-3303-2 |
| LT3682IDD#PBF | 制造商:Linear Technology 功能描述:DC-DC CONVERTER BUCK 2.2MHZ 制造商:Linear Technology 功能描述:DC-DC CONVERTER, BUCK, 2.2MHZ, DFN-12 |
| LT3682IDD#TRPBF | 功能描述:IC REG BUCK ADJ 1A 12DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT3682IDD-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:1A Micropower Step-Down |
发布紧急采购，3分钟左右您将得到回复。