- 您现在的位置：买卖IC网 > PDF目录44986 > LT3686IDD#TRPBF (LINEAR TECHNOLOGY CORP) 2.65 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PDSO10 PDF资料下载
参数资料
| 型号： | LT3686IDD#TRPBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | 2.65 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PDSO10 |
| 封装： | 3 X 3 MM, LEAD FREE, PLASTIC, MO-229WEED-2, DFN-10 |
| 文件页数： | 10/28页 |
| 文件大小： | 509K |
| 代理商： | LT3686IDD#TRPBF |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LT3686
18
3686fc
ApplicAtions inForMAtion
below the minimum voltage to sustain boosted operation
(2.2V across the boost capacitor), the output voltage will
fall suddenly to:
VOUT = (VIN–2.2)DCMAX
Figure 9 shows the minimum VIN necessary to sustain
boosted operation during dropout. Once VIN drops below
the sustain voltage, VIN will need to reach the start voltage
again to refresh the boost capacitor. The programmable
undervoltage lockout (UVLO) function can be used to
avoid operating unless VINisgreaterthanthestartvoltage.
Fixed Frequency at Light Load
The LT3686 contains unique active load circuitry to allow
for full frequency switching at very light loads. To enable
the active load, tie the MODE pin to greater than 0.8V.
Typical fixed frequency nonsynchronous buck regulators
skip pulses at light loads. With a fixed input voltage, as
the load current decreases in discontinuous mode, the
regulator is required to switch for shorter periods of time.
When the required on time decreases below the typical
minimum on time, the regulator skips one or more pulses
so the effective average duty cycle is equal to the required
duty cycle. This likelihood of entering pulse-skipping is
exacerbated by the tendency for minimum on time to
increase at very light loads. Pulse-skipping is undesirable
because it causes unpredictable, sub-harmonic output
ripplethatcaninterferewiththeoperationofothersensitive
components such as AM receivers and audio equipment.
The BD active load is designed to combat pulse-skipping
by providing an operational regime between full frequency
discontinuous and pulse-skipping modes.
The maximum VIN before pulse-skipping in discontinu-
ous mode is directly dependent on load current; as the
load decreases, so does the pulse-skipping boundary. An
artificial load on the output helps push the pulse-skipping
boundary higher. The LT3686 achieves this goal by com-
manding the minimum load necessary to keep itself at
full switching frequency, hence the circuitry is called an
active load.
AstheLT3686approachesminimumontimeindiscontinu-
ous mode, its power switch transitions smoothly into a
fixed on time, fixed frequency open loop current source.
Instead of controlling switch current, the internal error
amplifier servos the active load on the output via the BD
pin to maintain output voltage regulation. The impact on
efficiency is mitigated by pulling the minimum current
necessary to keep switching at full frequency. The neces-
sary BD load to maintain output regulation depends on
VIN, inductor size, and load current. As the necessary
BD load increases beyond its 40mA limit, pulse-skipping
mode will resume.
The BD active load circuitry is enabled when MODE tied
high and disabled when MODE is tied low. Even when
activated, the active load will shutdown when BD voltage
exceeds either 5.2V or VIN in an effort to minimize power
dissipationandintelligentlyreacttoexternalconfigurations.
To address the startup concerns delineated in the BOOST
and BD Pin Considerations section, the active load will
assist startup by pulling maximum current (40mA) to
charge the boost capacitor voltage in the absence of an
adequate load. An internal power good circuit will disable
the BD active load when VFB reaches 0.7V. Figure 9 com-
pares plots of minimum input voltage to start and run as
a function of load current. In many cases the discharged
output capacitor will present a load to the switcher which
will allow it to start. The plots show the worst-case situ-
ation where VIN is ramping very slowly.
The active load also activates to hasten the recharge of
boost cap when operating beyond maximum duty cycle.
When not in use, the active load pulls no current.
Figure 10. Regions of Operation (5VOUT, 2MHz)
IOUT (mA)
0
V IN
(V)
5
10
20
25
35
30
40
15
20
40
60
100
120
140
80
3686 F10
CCM
DCM
ACTIVE
LOAD
PULSE-SKIPPING
相关PDF资料 |
PDF描述 |
|---|---|
| LT3688IFE#TRPBF | SWITCHING REGULATOR, PDSO24 |
| LT3688EUF#PBF | SWITCHING REGULATOR, PQCC24 |
| LT3688IFE#PBF | SWITCHING REGULATOR, PDSO24 |
| LT3688HFE#PBF | SWITCHING REGULATOR, PDSO24 |
| LT3688HFE#TRPBF | SWITCHING REGULATOR, PDSO24 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3688 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual 800mA Step-Down Switching Regulator with Power-On Reset |
| LT3688EFE#PBF | 功能描述:IC REG BUCK ADJ 0.8A DL 24TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:MIC23xxx HyperLight Load™ Regulators 标准包装:5,000 系列:HyperLight Load® 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.8V 输入电压:2.7 V ~ 5.5 V PWM 型:混合物 频率 - 开关:4MHz 电流 - 输出:2A 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘，8-MLF? 包装:带卷 (TR) 供应商设备封装:8-MLF?（2x2） 产品目录页面:1094 (CN2011-ZH PDF) 其它名称:576-3303-2 |
| LT3688EFE#TRPBF | 功能描述:IC REG BUCK ADJ 0.8A DL 24TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT3688EFEPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual 800mA Step-Down Switching Regulator with Power-On Reset |
| LT3688EUF#PBF | 功能描述:IC REG BUCK ADJ 0.8A DL 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
发布紧急采购，3分钟左右您将得到回复。