参数资料
型号: LT3694EUFD#TRPBF
厂商: Linear Technology
文件页数: 7/28页
文件大小: 338K
描述: IC REG TRPL BUCK/LINEAR 28QFN
标准包装: 2,500
拓扑: 降压(降压)(1),线性(LDO)(2)
功能: 任何功能
输出数: 3
频率 - 开关: 250kHz ~ 2.5MHz
电压/电流 - 输出 1: 0.75 V ~ 16 V,2.6A
电压/电流 - 输出 2: 控制器
电压/电流 - 输出 3: 控制器
带 LED 驱动器:
带监控器:
带序列发生器:
电源电压: 4 V ~ 36 V
工作温度: -40°C ~ 125°C
安装类型: 表面贴装
封装/外壳: 28-WFQFN 裸露焊盘
供应商设备封装: 28-QFN(4x5)
包装: 带卷 (TR)
LT3694/LT3694-1
7
36941fb
PIN FUNCTIONS
V
IN
 (Pin 1/Pins 27, 28): The V
IN
 pin supplies power to the
internal switch of the 2.6A regulator and to the LT3694s
internal reference and start-up circuitry. This pin must be
locally bypassed.
EN/UVLO (Pin 2/Pin 1): The EN/UVLO pin is used to shut 
down the LT3694. It can be driven from a logic level or
used as an undervoltage lockout by connecting a resistor
divider from V
IN
.
CLKOUT (Pin 3/Pin 2): Digital Clock Output. The CLKOUT 
pin allows synchronization of other switching regulators
(LT3694-1 only).
SYNC (Pin 3/Pin 2): Frequency Synchronization Input. 
Connect a frequency source to this input if synchronization
is desired. Connect SYNC to ground if not used (LT3694
only).
PGOOD (Pin 4/Pin 3): Open Collector Output. PGOOD is 
pulled low when any of the three regulators drops out of
regulation (V
FB
 < 90% of nominal value).
RT (Pin 5/Pin 4): The RT pin requires a resistor to ground 
to set the operating frequency of the LT3694. If synchroniz-
ing the LT3694 to an external clock, the resistor should
be set to program the frequency at least 20% below the
synchronization frequency.
TRK/SS1, TRK/SS2 , TRK/SS3 (Pins 6, 7, 14/Pins 5, 6, 17): 
The TRK/SS pins allow a regulator to track the output of
another regulator. When the TRK/SS pin is below 0.75V,
the FB pin regulates to the TRK/SS voltage. This pin can
also be used as a soft-start by connecting a capacitor from
TRK/SS to ground. The TRK/SS pins should be left open
if neither feature is used.
FB1, FB2, FB3 (Pins 15, 8, 13/Pins 18, 7, 16): Negative 
Inputs of the Error Amplifiers. The LT3694 regulates each
feedback pin to the lesser of 0.75V or the corresponding
TRK/SS pin voltage. Connect the feedback resistor divider
taps to these pins.
DRV2, DRV3 (Pins 9, 12/Pins 8, 15): The DRV pins 
provide the base drive for the external NPN transistors
for the LDO regulators. The DRV pins can provide up to
6V of base drive.
LIM2, LIM3 (Pins 10, 11/Pins 9, 14): The LIM pins provide 
current limiting on the LDO pass transistors by sensing
a voltage on an external sense resistor connected to the
BIAS pin. These pins should be connected to BIAS if this
function is not used.
GND (Pins 10, 11, 12, 13, 25, 26) UFD Package Only: 
Power and Signal Ground.
V
C1
 (Pin 16/Pin 19): Output of the Internal Error Amp. 
The voltage on this pin controls the peak switch cur-
rent. This pin is normally used to compensate the
control loop. The switching regulator can be shut
down by pulling the V
C1
 pin to ground with an NMOS
or NPN transistor.
BIAS (Pin 17/Pin 20): The BIAS pin supplies the current 
to the LT3694s internal regulator and boost circuits. This
must be connected to a voltage source above 3V, usually
to V
OUT1
. The LDO pass transistor base current will also
come from the BIAS pin if it is at least 1.8V above the
LDO output.
BST (Pin 18/Pin 21): The BST pin is used to provide a 
drive voltage, higher than the input voltage, to the internal
bipolar NPN power switch.
DA (Pin 19/Pin 22): The DA pin senses the catch diode 
current to prevent excessive inductor current in output
overload or short-circuit conditions.
SW (Pin 20/Pins 23, 24): Output of the Internal Power 
Switch. Connect this pin to the inductor and switching
diode.
Exposed Pad (Pin 21/Pin 29): Ground. The underside 
exposed pad metal of the package provides both electrical
contact to ground and a conductive thermal path to the
printed circuit board. The Exposed Pad must be soldered to
a grounded pad on the circuit board for proper operation.
(FE/UFD)
相关PDF资料
PDF描述
LT1939EDD#PBF IC REG DL BUCK/LINEAR 12DFN
T95Y685M025LZAL CAP TANT 6.8UF 25V 20% 2910
V48C12H75BG2 CONVERTER MOD DC/DC 12V 75W
ISL6612ACBZAR5214 IC MOSFET DRVR SYNC BUCK 8-SOIC
CS5463-ISZR IC ENERGY METERING 1PHASE 24SSOP
相关代理商/技术参数
参数描述
LT3694IFE#PBF 功能描述:IC REG TRPL BUCK/LINEAR 20TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压(降压)同步(3),线性(LDO)(2) 功能:任何功能 输出数:5 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:5.6 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:*
LT3694IFE#TRPBF 功能描述:IC REG TRPL BUCK/LINEAR 20TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压(降压)同步(3),线性(LDO)(2) 功能:任何功能 输出数:5 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:5.6 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:*
LT3694IFE-1#PBF 功能描述:IC REG TRPL BUCK/LINEAR 20TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压(降压)同步(3),线性(LDO)(2) 功能:任何功能 输出数:5 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:5.6 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:*
LT3694IFE-1#TRPBF 功能描述:IC REG TRPL BUCK/LINEAR 20TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压(降压)同步(3),线性(LDO)(2) 功能:任何功能 输出数:5 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:5.6 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:*
LT3694IFEPBF 制造商:LINER 制造商全称:Linear Technology 功能描述:36V, 2.6A Monolithic Buck Regulator With Dual LDO