- 您现在的位置：买卖IC网 > PDF目录20621 > LT3694IFE#TRPBF (Linear Technology)IC REG TRPL BUCK/LINEAR 20TSSOP PDF资料下载
参数资料
| 型号： | LT3694IFE#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 12/28页 |
| 文件大小： | 338K |
| 描述： | IC REG TRPL BUCK/LINEAR 20TSSOP |
| 标准包装： | 2,500 |
| 拓扑： | 降压（降压）（1），线性（LDO）（2） |
| 功能： | 任何功能 |
| 输出数： | 3 |
| 频率 - 开关： | 250kHz ~ 2.5MHz |
| 电压/电流 - 输出 1： | 0.75 V ~ 16 V，2.6A |
| 电压/电流 - 输出 2： | 控制器 |
| 电压/电流 - 输出 3： | 控制器 |
| 带 LED 驱动器： | 无 |
| 带监控器： | 无 |
| 带序列发生器： | 是 |
| 电源电压： | 4 V ~ 36 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-TSSOP（0.173"，4.40mm 宽）裸露焊盘 |
| 供应商设备封装： | 20-TSSOP-EP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页当前第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LT3694/LT3694-1
12
36941fb
APPLICATIONS INFORMATION
where f is the switching frequency of the LT3694 and L
is the value of the inductor. The peak inductor and switch
current is:
I
SWPK
=I
LPK
=I
OUT
+
I
L
2
To maintain output regulation, this peak current must be
less than the LT3694s switch current limit, I
LIM
. I
LIM
is at
least 3.5A at low duty cycles (0.1) and decreases linearly
to 2.8A at DC = 0.8.
The minimum inductance can now be calculated as:
L
MIN
=
1DC
MIN
2 f
V
OUT
+V
F
I
LIM
I
OUT
However, its generally better to use an inductor larger
than the minimum value. The minimum inductor has large
ripple currents which increase core losses and require
large output capacitors to keep output voltage ripple low.
Select an inductor greater than L
MIN
that keeps the ripple
current below 30% of I
LIM
.
For input voltages greater than 30V, use an inductor with
a saturation current of 6A or greater and an inductance
value of 3.3礖 or greater.
The inductors RMS current rating must be greater than the
maximum load current and its saturation current should
be greater than I
LPK
. For highest efficiency, the series
resistance (DCR) should be less than 0.1? Table 2 lists
several vendors and types that are suitable.
Table 2. Inductors
SERIES
INDUCTANCE
RANGE (礖)
CURRENT
RANGE (A) MANUFACTURER
WE-HC
1 to 6.5 6 to 15 W黵th Elektronik
www.we-online.com
MSS1048
0.8 to 8
4 to 8 Coilcraft
www.coilcraft.com
CDRH103R
0.8 to 10 2.8 to 8.3 Sumida
www.sumida.com
VLF
2.2 to 10 3.8 to 7.7 TDK
www.component.tdk.
com
IHLP-2525CZ-11 1 to 10 2.5 to 9.5 Vishay
www.vishay.com
This analysis is valid for continuous mode operation
(I
OUT
> I
LIM
/2). For details of maximum output current in
discontinuous mode operation, see the Linear Technol-
ogy Application Note 44. Finally, for duty cycles greater
than 50% (V
OUT
/V
IN
> 0.5), a minimum inductance is
required to avoid subharmonic oscillations. This minimum
inductance is:
L
MIN
=
(V
OUT
+V
F
)
2A f
SW
with L
MIN
in 糎 and f
SW
in MHz. A detailed discussion
of subharmonic oscillations can be found in the Linear
Technology Application Note 19.
Input Capacitor Selection
Bypass the input of the LT3694 circuit with a ceramic
capacitor of X7R or X5R type. Y5V types have poor
performance over temperature and applied voltage, and
should not be used. A 4.7礔 to 22糉 ceramic capacitor
is adequate to bypass the LT3694 and will easily handle
the ripple current. Use a 22礔 capacitor with f
SW
between
250kHz and 800kHz. Use a 10礔 capacitor with f
SW
be-
tween 800kHz and 1.6MHz. Use a 4.7礔 capacitor above
1.6MHz. Always check for sufficient margin by reducing
the capacitor value until the dropout increases by >500mV.
If the input power source has high impedance, or there
is significant inductance due to long wires or cables,
additional bulk capacitance may be necessary. This
can be provided with a lower performance electrolytic
capacitor.
Step-down regulators draw current from the input sup-
ply in pulses with very fast rise and fall times. The input
capacitor is required to reduce the resulting voltage
ripple at the LT3694 and to force this very high frequency
switching current into a tight local loop, minimizing EMI.
A 10糉 capacitor is capable of this task, but only if it is
placed close to the LT3694 and the catch diode (see the
PCB Layout section). A second precaution regarding the
ceramic input capacitor concerns the maximum input
voltage rating of the LT3694. A ceramic input capacitor
combined with trace or cable inductance forms a high
相关PDF资料 |
PDF描述 |
|---|---|
| FIN0.50RD | FIREFLEX FIBERGLASS 1/2" RED 100 |
| LT3694IFE-1#PBF | IC REG TRPL BUCK/LINEAR 20TSSOP |
| LT3694IFE#PBF | IC REG TRPL BUCK/LINEAR 20TSSOP |
| ISL6594ACRZ-T | IC MOSFET DRVR SYNC BUCK 10-DFN |
| C1005X6S1H223M | CAP CER 0.022UF 50V 20% X6S 0402 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3694IUFD#PBF | 功能描述:IC REG TRPL BUCK/LINEAR 28QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压（降压）同步（3），线性（LDO）（2） 功能:任何功能 输出数:5 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:5.6 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
| LT3694IUFD#TRPBF | 功能描述:IC REG TRPL BUCK/LINEAR 28QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压（降压）同步（3），线性（LDO）（2） 功能:任何功能 输出数:5 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:5.6 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
| LT3694IUFD-1#PBF | 功能描述:IC REG TRPL BUCK/LINEAR 28QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压（降压）同步（3），线性（LDO）（2） 功能:任何功能 输出数:5 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:5.6 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
| LT3694IUFD-1#TRPBF | 功能描述:IC REG TRPL BUCK/LINEAR 28QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压（降压）同步（3），线性（LDO）（2） 功能:任何功能 输出数:5 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:5.6 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
| LT3694IUFDPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:36V, 2.6A Monolithic Buck Regulator With Dual LDO |
发布紧急采购，3分钟左右您将得到回复。