- 您现在的位置：买卖IC网 > PDF目录13935 > LT3695IMSE-5#PBF (Linear Technology)IC REG BUCK 5V 1A 16MSOP PDF资料下载
参数资料
| 型号： | LT3695IMSE-5#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 14/30页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK 5V 1A 16MSOP |
| 标准包装： | 37 |
| 类型： | 降压（降压） |
| 输出类型： | 固定 |
| 输出数： | 1 |
| 输出电压： | 5V |
| 输入电压： | 3.6 V ~ 36 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 250kHz ~ 2.2MHz |
| 电流 - 输出： | 1A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TFSOP（0.118"，3.00mm 宽）裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 16-MSOP，裸露焊盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
LT3695 Series
APPLICATIONS INFORMATION
Inductor Selection and Maximum Output Current
A good ?rst choice for the inductor value is:
The current in the inductor is a triangle wave with an av-
erage value equal to the load current. The peak inductor
and switch current is:
L = ( V OUT + V D ) ?
1.8
f SW
I SW ( PEAK ) = I L ( PEAK ) = I OUT ( MAX ) +
Δ I L
2
( 1 ? DC ) ?( V OUT + V D )
wheref SW istheswitchingfrequencyinMHz,V OUT isthe
output voltage, V D is the catch diode drop (~0.5V) and L
is the inductor value in μH.
The inductor’s RMS current rating must be greater than the
maximum load current and its saturation current should be
about 30% higher. To keep the ef?ciency high, the series
resistance (DCR) should be less than 0.1Ω, and the core
material should be intended for high frequency applications.
Table 2 lists several vendors and suitable types.
For robust operation in fault conditions (start-up or short-
circuit) and high input voltage (>30V), the saturation
current should be chosen high enough to ensure that the
inductor peak current does not exceed 3.5A. For example,
an application running from an input voltage of 36V
using a 10μH inductor with a saturation current of 2.5A
will tolerate the mentioned fault conditions.
The optimum inductor for a given application may differ
from the one indicated by this simple design guide. A larger
value inductor provides a higher maximum load current
and reduces the output voltage ripple. If your load is lower
than the maximum load current, then you can relax the
value of the inductor and operate with higher ripple cur-
rent. This allows you to use a physically smaller inductor,
or one with a lower DCR resulting in higher ef?ciency.
Be aware that if the inductance differs from the simple
rule above, then the maximum load current will depend
on input voltage. In addition, low inductance may result
in discontinuous mode operation, which further reduces
maximum load current. For details of maximum output
where I L(PEAK) is the peak inductor current, I OUT(MAX) is
the maximum output load current and Δ I L is the inductor
ripple current. The LT3695 regulators limit their switch
current in order to protect themselves and the system
from overload faults. Therefore, the maximum output
current that the LT3695 regulators will deliver depends on
the switch current limit, the inductor value and the input
and output voltages.
When the switch is off, the potential across the inductor
is the output voltage plus the catch diode drop. This gives
the peak-to-peak ripple current in the inductor:
Δ I L =
L ? f SW
where f SW is the switching frequency of the LT3695
regulators, DC is the duty cycle and L is the value of the
inductor.
To maintain output regulation, the inductor peak current
must be less than the LT3695 regulators’ switch current
limit, I LIM . If the SYNC pin is grounded, I LIM is at least
1.45A at low duty cycles and decreases to 1.1A at DC =
90%. If the SYNC pin is tied to 0.8V or more or if it is
tied to a clock source for synchronization, I LIM is at least
1.18A at low duty cycles and decreases to 0.85A at DC =
90%. The maximum output current is also a function of
the chosen inductor value and can be approximated by
the following expressions depending on the SYNC pin
con?guration:
For the SYNC pin grounded:
Δ I L Δ I L
current and discontinuous mode operation, see Linear
Technology’s Application Note 44. Finally, for duty cycles
greater than 50% (V OUT /V IN > 0.5), a minimum inductance
I OUT ( MAX ) = I LIM ?
2 2
= 1 . 45 A ?( 1 ? 0 . 24 ? DC ) ?
is required to avoid sub-harmonic oscillations:
For the SYNC pin tied to 0.8V or more, or tied to a clock
Δ I L Δ I L
I OUT ( MAX ) = I LIM ? = 1 . 18 A ?( 1 ? 0 . 29 ? DC ) ?
L MIN = ( V OUT + V D ) ?
1.2
f SW
source for synchronization:
2 2
3695fa
14
相关PDF资料 |
PDF描述 |
|---|---|
| 16ML68MEFC6.3X5 | CAP ALUM 68UF 16V 20% RADIAL |
| 10ML120MEFC6.3X7 | CAP ALUM 120UF 10V 20% RADIAL |
| 6.3NA100MEFC5X11 | CAP ALUM 100UF 6.3V 20% BI-P RAD |
| ECC19DRXS-S734 | CONN EDGECARD 38POS DIP .100 SLD |
| 50NA2.2MEFC5X11 | CAP ALUM 2.2UF 50V 20% BI-P RAD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3695IMSEPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:1A Fault Tolerant Micropower Step-Down Regulator |
| LT3695IMSETRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:1A Fault Tolerant Micropower Step-Down Regulator |
| LT370 | 功能描述:标准LED-通孔 Green RoHS:否 制造商:Vishay Semiconductors 照明颜色:Red 光强度:0.7 mcd 波长/色温:615 nm 显示角:45 deg 透镜颜色/类型:Clear, Non-Diffused 正向电流:70 mA 正向电压:1.83 V to 3.03 V LED 大小:2 mm 系列: 封装:Tube |
| LT370_1 | 制造商:SEOUL 制造商全称:Seoul Semiconductor 功能描述:GREEN LAMP LED |
| LT370Z | 制造商:SEOUL 制造商全称:Seoul Semiconductor 功能描述:GREEN OVAL LAMP LED |
发布紧急采购，3分钟左右您将得到回复。