- 您现在的位置：买卖IC网 > PDF目录30768 > LT3695IMSE-5#TRPBF (LINEAR TECHNOLOGY CORP) 2 A SWITCHING REGULATOR, 2420 kHz SWITCHING FREQ-MAX, PDSO16 PDF资料下载
参数资料
| 型号： | LT3695IMSE-5#TRPBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | 2 A SWITCHING REGULATOR, 2420 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封装： | LEAD FREE, PLASTIC, MSOP-16 |
| 文件页数： | 13/30页 |
| 文件大小： | 491K |
| 代理商： | LT3695IMSE-5#TRPBF |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
LT3695 Series
20
3695fa
This reduces the minimum input voltage to approximately
300mV above VOUT. At higher load currents, the inductor
current is continuous and the duty cycle is limited by the
maximum duty cycle of the LT3695 regulators, requiring
a higher input voltage to maintain regulation.
Soft-Start
The RUN/SS pin can be used to soft-start the LT3695
regulators, reducing the maximum input current during
start-up. The RUN/SS pin is driven through an external
RC network to create a voltage ramp at this pin. Figure 6
shows the start-up and shutdown waveforms with the
soft-start circuit. By choosing a large RC time constant,
the peak start-up current can be reduced to the current
that is required to regulate the output, with no overshoot.
Choose the value of the resistor so that it can supply 7.5μA
when the RUN/SS pin reaches 2.5V. For fault tolerant ap-
plications, see the discussion of the RUN/SS resistor in
the Fault Tolerance section.
Synchronization
To select low ripple Burst Mode operation, tie the SYNC
pin below 0.3V (this can be ground or a logic output).
Synchronizing the oscillator of the LT3695 regulators to
an external frequency can be done by connecting a square
wave (with 20% to 80% duty cycle) to the SYNC pin. The
square wave amplitude should have valleys that are below
0.3V and peaks that are above 0.8V (up to 6V).
The LT3695 regulators will not enter Burst Mode operation
at low output loads while synchronized to an external clock,
but instead will skip pulses to maintain regulation.
The maximum load current that the part can supply is
reduced when a clock signal is applied to SYNC.
The LT3695 regulators may be synchronized over a 300kHz
to 2.2MHz range. The RT resistor should be chosen to set
the LT3695 regulators switching frequency 20% below the
lowest synchronization input. For example, if the synchro-
nization signal is 360kHz, the RT should be chosen for
300kHz. To assure reliable and safe operation the LT3695
regulators will only synchronize when the output voltage is
near regulation as indicated by the PG ag. It is therefore
necessary to choose a large enough inductor value to
supply the required output current at the frequency set
by the RT resistor. See the Inductor Selection section for
more information. It is also important to note that slope
compensation is set by the RT value; to avoid subharmonic
oscillations, calculate the minimum inductor value using
the frequency determined by RT.
Shorted and Reversed Input Protection
If the inductor is chosen so that it will not saturate exces-
sively, the LT3695 regulators will tolerate a shorted output.
When operating in short-circuit condition, the LT3695
regulators will reduce their frequency until the valley cur-
rent is at a typical value of 1.6A (see Figure 7). There is
another situation to consider in systems where the output
will be held high when the input to the LT3695 regulators is
absent. This may occur in battery charging applications or
in battery backup systems where a battery or some other
supply is diode ORed with the LT3695 regulators’ output.
If the VIN pin is allowed to oat and the RUN/SS pin is held
high (either by a logic signal or because it is tied to VIN),
APPLICATIONS INFORMATION
5ms/DIV
VRUN/SS
5V/DIV
VOUT
5V/DIV
IL
1A/DIV
VRUN
5V/DIV
3695 F05
RUN
15k
0.22μF
RUN/SS
GND
Figure 6. To Soft-Start the LT3695 Regulators,
Add a Resistor and Capacitor to the RUN/SS Pin
3695 F07
IL
500mA/DIV
VSW
20V/DIV
0V
0A
2μs/DIV
Figure 7. The LT3695 Regulators Reduce Their Frequency
to Protect Against Shorted Output with 36V Input
相关PDF资料 |
PDF描述 |
|---|---|
| LT3695EMSE-3.3#PBF | 2 A SWITCHING REGULATOR, 2420 kHz SWITCHING FREQ-MAX, PDSO16 |
| LT3695EMSE-3.3#TRPBF | 2 A SWITCHING REGULATOR, 2420 kHz SWITCHING FREQ-MAX, PDSO16 |
| LT3751IUFD#TR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC20 |
| LT3751IUFD#TRPBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC20 |
| LT3751EFE | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO20 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3695IMSEPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:1A Fault Tolerant Micropower Step-Down Regulator |
| LT3695IMSETRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:1A Fault Tolerant Micropower Step-Down Regulator |
| LT370 | 功能描述:标准LED-通孔 Green RoHS:否 制造商:Vishay Semiconductors 照明颜色:Red 光强度:0.7 mcd 波长/色温:615 nm 显示角:45 deg 透镜颜色/类型:Clear, Non-Diffused 正向电流:70 mA 正向电压:1.83 V to 3.03 V LED 大小:2 mm 系列: 封装:Tube |
| LT370_1 | 制造商:SEOUL 制造商全称:Seoul Semiconductor 功能描述:GREEN LAMP LED |
| LT370Z | 制造商:SEOUL 制造商全称:Seoul Semiconductor 功能描述:GREEN OVAL LAMP LED |
发布紧急采购，3分钟左右您将得到回复。