- 您现在的位置：买卖IC网 > PDF目录79789 > LT3748EMS#TRPBF (LINEAR TECHNOLOGY CORP) SWITCHING CONTROLLER, PDSO12 PDF资料下载
参数资料
| 型号： | LT3748EMS#TRPBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING CONTROLLER, PDSO12 |
| 封装： | LEAD FREE, PLASTIC, MSOP-16/12 |
| 文件页数： | 3/30页 |
| 文件大小： | 284K |
| 代理商： | LT3748EMS#TRPBF |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
LT3748
11
3748fa
APPLICATIONS INFORMATION
Minimum Primary Inductance Requirements
The LT3748 obtains output voltage information from the
external MOSFET drain voltage when the secondary winding
conducts current. The sampling circuitry needs a minimum
of 400ns to settle and sample the output voltage while the
MOSFET switch is off. This required settle and sample
time is controlled by external components independent of
the minimum off-time of the GATE pin as specified in the
Electrical Characteristics table. The electrical specification
minimum off-time is based on an internal timer and acts
as a maximum frequency clamp. The following equation
gives the minimum value for primary-side magnetizing
inductance:
LPRI ≥
VOUT + VF(DIODE)
() RSENSE tSETTLE(MIN) NPS
VSENSE(MIN)
VSENSE(MIN) = 15mV
tSETTLE(MIN) = 400ns
NPS = Ratio of primary windings to secondary windings
In addition to the primary inductance requirement for
minimum settling and sampling time, the LT3748 has
internal circuit constraints that prevent it from setting the
GATE node high for shorter than approximately 250ns.
If the inductor current exceeds the desired current limit
during that time oscillation may occur at the output as
the current control loop will lose its ability to regulate.
Therefore, the following equation relating to maximum
input voltage must also be followed in selecting primary-
side magnetizing inductance:
LPRI ≥
VIN(MAX)RSENSE tON(MIN)
VSENSE(MIN)
tON(MIN) = 250ns
The last constraint on minimum inductance value would
relate to minimum full-load operating frequency, fMIN, and
is derived from fSW = 1/(tON + tOFF):
LPRI≤VIN(MIN)(VOUT+VF(DIODE))NPS/(fSW(MIN)ILIM
((VOUT + VF(DIODE)) NPS + VIN(MIN)))
The minimum operating frequency may be lower than
the calculated number due to delays in detecting current
limit and detecting boundary mode that are specific to
each application.
Output Power
Because the MOSFET power switch is located outside the
LT3748, the maximum output power is primarily limited
by external components. Output power limitations can
be separated into three categories—voltage limitations,
current limitations and thermal limitations.
The voltage limitations in a flyback design are primarily
the MOSFET switch VDS(MAX) and the output diode re-
verse-bias rating. Increasing the voltage rating of either
component will typically decrease application efficiency if
all else is equal and the voltage requirements on each of
those components will be directly related to the windings
ratio of the transformer, the input and output voltages
and the use of any additional snubbing components.
The MOSFET VDS(MAX) must theoretically be higher than
VIN(MAX) + (VOUT NPS) and the output diode reverse bias
must be higher than VOUT + (VIN(MAX)/NPS), though leak-
age inductance spikes on both the drain of the MOSFET
and the anode of the output diode may more than double
that requirement (see section on leakage inductance for
more details on snubbers). Figure 1 illustrates the effect
on available output power for several MOSFET voltage
ratings while continuously maximizing windings ratio
for input voltage with a fixed MOSFET current limit and
output voltage. Increasing the MOSFET rating increases
the possible windings ratio and or maximum input voltage
and can increase the available output power for a given
application. Both figures assume no leakage inductance
and high efficiency.
INPUT VOLTAGE (V)
0
MAXIMUM
OUTPUT
POWER
(W)
30
40
50
80
3748 F01
20
10
0
20
40
60
100
VDS = 200V
VDS = 150V
VDS = 100V
Figure 1. Maximum Output Power at 12VOUT with a
3A ILIM and Maximum VDS = 100V, 150V, 200V
相关PDF资料 |
PDF描述 |
|---|---|
| LM1001-7RD9AFU | 1-OUTPUT AC-DC REG PWR SUPPLY MODULE |
| LM1001-9PD9AFU | 1-OUTPUT AC-DC REG PWR SUPPLY MODULE |
| LM1301-7RD8AFU | 1-OUTPUT AC-DC REG PWR SUPPLY MODULE |
| LM1301-9PD4AFU | 1-OUTPUT AC-DC REG PWR SUPPLY MODULE |
| LM1501-7PD2AFU | 1-OUTPUT AC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3748HMS#PBF | 功能描述:IC REG CTRLR FLYBK ISO CM 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR |
| LT3748HMS#TRPBF | 功能描述:IC REG CTRLR FLYBK ISO CM 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LT3748HMSPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:100V Isolated Flyback Controller |
| LT3748HMSTRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:100V Isolated Flyback Controller |
| LT3748IMS#PBF | 功能描述:IC REG CTRLR FLYBK ISO CM 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。