- 您现在的位置：买卖IC网 > PDF目录20857 > LT3754EUH#PBF (Linear Technology)IC LED DRIVER AUTOMOTIVE 32QFN PDF资料下载
参数资料
| 型号： | LT3754EUH#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 21/30页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVER AUTOMOTIVE 32QFN |
| 标准包装： | 73 |
| 恒定电流： | 是 |
| 拓扑： | PWM，升压（升压） |
| 输出数： | 16 |
| 内部驱动器： | 无 |
| 类型 - 主要： | 车载，背光 |
| 类型 - 次要： | 白色 LED |
| 频率： | 100kHz ~ 1MHz |
| 电源电压： | 6 V ~ 40 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN |
| 包装： | 管件 |
| 工作温度： | -40°C ~ 125°C |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
LT3754
APPLICATIONS INFORMATION
LED Open Circuit and PWM Dimming Ratios
The LT3754 monitors each LED pin voltage to determine if
the LED string has an open fault (LED pin voltage < 0.5V).
If an open LED fault occurs, the FAULT flag is pulled low.
To avoid false detection of faults during the initial converter
start-up when V OUT is low, the LT3754 ignores low LED
pin voltages until V OUT reaches 90% of its maximum al-
lowed OVP level. Once this condition is met, the LT3754
monitors all LED pins for open LED faults. To avoid false
detection of faults during PWM dimming edges (where
LED pins can possibly ring and trip fault detection levels)
the LT3754 only monitors/updates fault conditions during
PWM high (and only after a blank duration of 2μs following
each PWM rising edge).
LED Short Circuit
A short circuit fault between the positive terminal of an LED
string (V OUT ) and the negative terminal of the LED string
(LEDx pin) causes the channel to be disabled in order to
protect the internal current source. A resistive short is
allowed as long as (V OUT -V LEDx ) < 6V. During the short,
however, cable inductance can cause the LED pin voltage
to overshoot past V OUT voltage. To avoid LED pin voltage
exceeding its absolute maximum rated voltage, a diode
may be required to clamp the LED pin. The anode of a
1N4148WS diode should be connected to the LED pin and
the cathode of the diode connected to the V OUT pin. Keep
the traces as short as possible. A Schottky diode should
not be used due to high reverse bias leakage currents.
Loop Compensation
Be sure to check the stability of the loop with the LEDs
connected (LED regulation loop) and disconnected
(Overvoltage Protection (OVP) regulation loop). Various
application circuits are shown in the data sheet which
cover a range of V IN , V OUT , f OSC , output power and inductor
current ripple values. For application requirements which
deviate from the circuits shown in the data sheet be sure
to check the stability of the final application over the full
V IN range, LED current range (if analog dimming) and
temperature range. Be aware that if the V C pin components
represent the dominant pole for the converter loop and
they have been adjusted to achieve stability, the V C pin
might move more slowly during load transient conditions
such as an all-LEDs-open fault. A slower moving V C pin
will add to V OUT overshoot during an all-LEDs-open fault.
An alternative compensation approach is to place the
dominant pole of the converter loop at the output. This
requires an increased output capacitor value but will allow
a much reduced Vc capacitor. The combination will allow
V C to move more quickly and V OUT to move more slowly
resulting in less overshoot during an all-LEDs-open fault.
Thermal Considerations
The internal power dissipation of the LT3754 comes from 3
main sources: V IN quiescent current (I Q total), V IN current
for GATE switching (I GATE ) and the LT3754 LED current
sources. Since the maximum operational V IN voltage is
40V, care should be taken when selecting the switching
frequency and type of external power MOSFET since the
current required from V IN for GATE switching is given by,
I GATE = f OSC ? Qg
where Q g is the gate charge (at V GS = INTV CC ) specified
for the MOSFET and f OSC is the programmed switching
frequency for the LT3754. A low Q g MOSFET should al-
ways be used when operating the LT3754 from high V IN
voltages. The internal junction temperature of the LT3754
can be estimated as:
T J = T A + [V IN ? ( I QTOTAL + (f OSC ? Q g )) + (16 ? I(LED X ) ? 1.1 V)]
? θ JA
where, T A is the ambient temperature for the LT3754
I QTOTAL represents the V IN quiescent current for the LT3754
(not switching, PWM = 1.5V and CTRL = 0.1V) - illustrated
in the Typical Characteristics Graphs – plus the base cur-
rents of active channels (typically 16 ? I(LED)/75). θ JA is
the thermal resistance of the package (34°C/W for the
5mm × 5mm QFN package).
3754fc
21
相关PDF资料 |
PDF描述 |
|---|---|
| LT3599HFE#TRPBF | IC LED DVR WHITE BCKLGT 28TSSOP |
| 1N5397G-T | DIODE STD REC 1.5A 600V DO-15 |
| P51-200-S-H-I12-4.5V-000-000 | SENSOR 200PSI M12-1.5 6G .5-4.5V |
| REC5-2409DRWZ/H6/A/CTRL | CONV DC/DC 5W 9-36VIN +/-09VOUT |
| P51-75-G-W-I36-20MA-000-000 | SENSOR 75PSI 1/8-27NPT 4-20MA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3754EUHTRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:16-Channel × 50mA LED Driver |
| LT3754IUH#PBF | 功能描述:IC LED DVR 16CH 50MA 32QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
| LT3754IUH#TRPBF | 功能描述:IC LED DVR 16CH 50MA 32QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
| LT3754IUHPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:16-Channel × 50mA LED Driver |
| LT3754IUHTRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:16-Channel × 50mA LED Driver |
发布紧急采购，3分钟左右您将得到回复。