- 您现在的位置：买卖IC网 > PDF目录15237 > LT3757MPMSE#PBF (Linear Technology)IC REG CTRLR PWM CM 10-MSOP PDF资料下载
参数资料
| 型号： | LT3757MPMSE#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 22/36页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR PWM CM 10-MSOP |
| 标准包装： | 50 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 1MHz |
| 电源电压： | 2.9 V ~ 40 V |
| 降压： | 无 |
| 升压： | 是 |
| 回扫： | 是 |
| 反相： | 是 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -55°C ~ 125°C |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
LT3757/LT3757A
APPLICATIONS INFORMATION
I SW(MAX) = I L1(MAX) + I L2(MAX) = I O(MAX) ?
SEPICConverter:SwitchDutyCycleandFrequency
For a SEPIC converter operating in CCM, the duty cycle
of the main switch can be calculated based on the output
voltage (V OUT ), the input voltage (V IN ) and the diode
forward voltage (V D ).
The maximum duty cycle (D MAX ) occurs when the converter
has the minimum input voltage:
In a SEPIC converter, the switch current is equal to I L1 +
I L2 when the power switch is on, therefore, the maximum
average switch current is defined as:
1
1 ? D MAX
and the peak switch current is:
I SW(PEAK) = ? 1 + ? ? I O(MAX) ?
D MAX =
V OUT + V D
V IN(MIN) + V OUT + V D
? 2 ?
? c ?
1
1 ? D MAX
I L1(MAX) = I IN(MAX) = I O(MAX) ?
SEPICConverter:InductorandSenseResistorSelection
As shown in Figure 1, the SEPIC converter contains two
inductors: L1 and L2. L1 and L2 can be independent, but can
also be wound on the same core, since identical voltages
are applied to L1 and L2 throughout the switching cycle.
For the SEPIC topology, the current through L1 is the
converter input current. Based on the fact that, ideally, the
output power is equal to the input power, the maximum
average inductor currents of L1 and L2 are:
D MAX
1 ? D MAX
I L2(MAX) = I O(MAX)
The constant c in the preceding equations represents the
percentage peak-to-peak ripple current in the switch, rela-
tive to I SW(MAX) , as shown in Figure 9. Then, the switch
ripple current ?I SW can be calculated by:
?I SW = c ? I SW(MAX)
The inductor ripple currents ?I L1 and ?I L2 are identical:
?I L1 = ?I L2 = 0.5 ? ? I SW
The inductor ripple current has a direct effect on the
choice of the inductor value. Choosing smaller values of
?I L requires large inductances and reduces the current
loop gain (the converter will approach voltage mode).
Accepting larger values of ?I L allows the use of low in-
ductances, but results in higher input current ripple and
greater core losses. It is recommended that c falls in the
range of 0.2 to 0.4.
I SW
I SW(MAX)
? I SW = χ ? I SW(MAX)
DT S
t
T S
3757 F08
Figure 9. The Switch Current Waveform of the SEPIC Converter
3757afd
22
相关PDF资料 |
PDF描述 |
|---|---|
| GBM40DTMS-S189 | CONN EDGECARD 80POS R/A .156 SLD |
| VE-J7N-EY-F2 | CONVERTER MOD DC/DC 18.5V 50W |
| ABC13DRYH | CONN EDGECARD 26POS .100 DIP SLD |
| NCP304HSQ29T1G | IC DETECTOR VOLTAGE 2.9V SC82AB |
| UPM1E182MHD6 | CAP ALUM 1800UF 25V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3757MPMSE-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Boost, Flyback, SEPIC and Inverting Controller |
| LT3758 | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Input Voltage, Boost, Flyback, SEPIC and Inverting Controller |
| LT3758A | 制造商:LINER 制造商全称:Linear Technology 功能描述:60V Low IQ Inverting DC/DC Controller Wide Operating VIN Range: 3.5V to 60V |
| LT3758AEDD#PBF | 制造商:Linear Technology 功能描述:IC REG CTRLR BST FLYBK INV 10DFN |
| LT3758AEDD#TRPBF | 制造商:Linear Technology 功能描述:IC REG CTRLR BST FLYBK INV 10DFN 制造商:Linear Technology 功能描述:SP-SWREG/Controller, High Input Voltage, Boost, Flyback, SEPIC and Inverting Con |
发布紧急采购，3分钟左右您将得到回复。