参数资料
| 型号： | LT3758EMSE#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 13/36页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR PWM CM 10-MSOP |
| 标准包装： | 50 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 1MHz |
| 电源电压： | 5.5 V ~ 100 V |
| 降压： | 无 |
| 升压： | 是 |
| 回扫： | 是 |
| 反相： | 是 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
LT3758/LT3758A
APPLICATIONS INFORMATION
Duty Cycle Consideration
Switching duty cycle is a key variable defining converter
operation. As such, its limits must be considered. Minimum
on-time is the smallest time duration that the LT3758 is
capable of turning on the power MOSFET. This time is
generally about 220ns (typical) (see Minimum On-Time
in the Electrical Characteristics table). In each switching
cycle, the LT3758 keeps the power switch off for at least
220ns (typical) (see Minimum Off-Time in the Electrical
Characteristics table).
The minimum on-time and minimum off-time and the
switching frequency define the minimum and maximum
switching duty cycles a converter is able to generate:
Minimum duty cycle = minimum on-time ? frequency
Maximum duty cycle = 1 – (minimum off-time ? frequency)
Programming the Output Voltage
The output voltage V OUT is set by a resistor divider, as
shown in Figure 1. The positive and negative V OUT are set
by the following equations:
Soft-Start
The LT3758 contains several features to limit peak switch
currents and output voltage (V OUT ) overshoot during
start-up or recovery from a fault condition. The primary
purpose of these features is to prevent damage to external
components or the load.
High peak switch currents during start-up may occur in
switching regulators. Since V OUT is far from its final value,
the feedback loop is saturated and the regulator tries to
charge the output capacitor as quickly as possible, resulting
in large peak currents. A large surge current may cause
inductor saturation or power switch failure.
The LT3758 addresses this mechanism with the SS pin.
As shown in Figure 1, the SS pin reduces the power
MOSFET current by pulling down the V C pin through
Q2. In this way the SS allows the output capacitor to
charge gradually toward its final value while limiting the
start-up peak currents. The typical start-up waveforms
are shown in the Typical Performance Characteristics
section. The inductor current I L slewing rate is limited by
the soft-start function.
V OUT,POSITIVE = 1.6V ? ? 1 +
?
?
R2 ?
R1 ? ?
Besides start-up (with SHDN /UVLO), soft-start can also
be triggered by the following faults:
V OUT,NEGATIVE = –0.8V ? ? 1 +
6V ? ? 1 +
> V OUT(MAX)
? ? + 3.5V ?
T SS = C SS ?
? R2 ?
?
? R1 ?
The resistors R1 and R2 are typically chosen so that
the error caused by the current flowing into the FBX pin
during normal operation is less than 1% (this translates
to a maximum value of R1 at about 158k).
In the applications where V OUT is pulled up by an external
positive power supply, the FBX pin is also pulled up through
the R2 and R1 network. Make sure the FBX does not exceed
its absolute maximum rating (6V). The R5, D2, and D3 in
Figure 1 provide a resistive clamp in the positive direction.
To ensure FBX is lower than 6V, choose sufficiently large
R1 and R2 to meet the following condition:
? R2 ? R2
? R1 8k ?
1. INTV CC > 17.5V
2. INTV CC < 4.5V
3. Thermal lockout
Any of these three faults will cause the LT3758 to stop
switching immediately. The SS pin will be discharged by
Q3. When all faults are cleared and the SS pin has been
discharged below 0.2V, a 10μA current source I S2 starts
charging the SS pin, initiating a soft-start operation.
The soft-start interval is set by the soft-start capacitor
selection according to the equation:
1.25V
10μA
where V OUT(MAX) is the maximum V OUT that is pulled up
by an external power supply.
3758afd
13
相关PDF资料 |
PDF描述 |
|---|---|
| LT3759EMSE#PBF | IC REG CTRLR BST INV PWM 12-MSOP |
| LT3781IG#TRPBF | IC REG CTRLR ISO PWM CM 20-SSOP |
| LT3782EUFD#PBF | IC REG CTRLR BST PWM CM 28-QFN |
| LT3800IFE#PBF | IC REG CTRLR INV PWM CM 16-TSSOP |
| LT3804EFE#PBF | IC REG CTRLR ISO PWM 28-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3758EMSETRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Input Voltage, Boost, Flyback, SEPIC and Inverting Controller |
| LT3758HMSE | 制造商:Linear Technology 功能描述: |
| LT3758HMSE#PBF | 功能描述:IC REG CTRLR PWM CM 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LT3758HMSE#TRPBF | 功能描述:IC REG CTRLR PWM CM 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LT3758IDD#PBF | 功能描述:IC REG CTRLR BST FLYBK INV 10DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。