- 您现在的位置：买卖IC网 > PDF目录15318 > LT3759IMSE#PBF (Linear Technology)IC REG CTRLR BST INV PWM 12-MSOP PDF资料下载
参数资料
| 型号： | LT3759IMSE#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 23/32页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BST INV PWM 12-MSOP |
| 标准包装： | 37 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 1MHz |
| 电源电压： | 1.6 V ~ 42 V |
| 降压： | 无 |
| 升压： | 是 |
| 回扫： | 无 |
| 反相： | 是 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 12-TSSOP （0.118"，3.00mm 宽）裸露焊盘 |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
LT3759
APPLICATIONS INFORMATION
V OUT – V D
? V OUT(P ? P) = ? I L2 ? ESR COUT +
I RMS(CDC) > I O(MAX) ?
InvertingConverter:SwitchDutyCycleandFrequency
For an inverting converter operating in CCM, the duty
cycle of the main switch can be calculated based on the
negative output voltage (V OUT ) and the input voltage (V IN ).
The maximum duty cycle (D MAX ) occurs when the converter
has the minimum input voltage:
D MAX =
V OUT – V D – V IN(MIN)
Inverting Converter: Inductor, Sense Resistor, Power
MOSFET, Output Diode and Input Capacitor Selections
The selections of the inductor, sense resistor, power
MOSFET, output diode and input capacitor of an inverting
converter are similar to those of the SEPIC converter. Please
refer to the corresponding SEPIC converter sections.
Inverting Converter: Output Capacitor Selection
The inverting converter requires much smaller output
capacitors than those of the boost and SEPIC converters
for similar output ripples. This is due to the fact that, in
the inverting converter, the inductor L2 is in series with the
output, and the ripple current flowing through the output
capacitors are continuous. The output ripple voltage is
produced by the ripple current of L2 flowing through the
ESR and bulk capacitance of the output capacitor:
? 1 ?
? 8 ? f OSC ? C OUT ?
After specifying the maximum output ripple, the user can
select the output capacitors according to the preceding
equation.
The ESR can be minimized by using high quality X5R or
X7R dielectric ceramic capacitors. In many applications,
ceramic capacitors are sufficient to limit the output volt-
age ripple.
The RMS ripple current rating of the output capacitor
needs to be greater than:
I RMS(COUT) > 0.3 ? D I L2
Inverting Converter: Selecting the DC Coupling
Capacitor
The DC voltage rating of the DC coupling capacitor (C DC ,
as shown in Figure 9) should be larger than the maximum
input voltage minus the output voltage (negative voltage):
V CDC > V IN(MAX) – V OUT
C DC has nearly a rectangular current waveform. During
the switch off-time, the current through C DC is I IN , while
approximately –I O flows during the on-time. The RMS
rating of the coupling capacitor is determined by the fol-
lowing equation:
D MAX
1 – D MAX
A low ESR and ESL, X5R or X7R ceramic capacitor works
well for C DC .
Board Layout
The high speed operation of the LT3759 demands careful
attention to board layout and component placement. The
exposed pad of the package is the only GND terminal of
the IC, and is important for thermal management of the
IC. Therefore, it is crucial to achieve a good electrical and
thermal contact between the exposed pad and the ground
plane of the board. For the LT3759 to deliver its full output
power, it is imperative that a good thermal path be pro-
vided to dissipate the heat generated within the package.
It is recommended that multiple vias in the printed circuit
board be used to conduct heat away from the IC and into
a copper plane with as much area as possible.
To prevent radiation and high frequency resonance prob-
lems, proper layout of the components connected to the
IC is essential, especially the power paths with higher di/
dt. The following high di/dt loops of different topologies
should be kept as tight as possible to reduce inductive
ringing:
? In boost configuration, the high di/dt loop contains the
output capacitor, the sensing resistor, the power MOSFET
and the Schottky diode.
3759fc
For more information www.linear.com/3759
23
相关PDF资料 |
PDF描述 |
|---|---|
| VE-JWD-EW-F1 | CONVERTER MOD DC/DC 85V 100W |
| LTC695ISW | IC MPU SUPERVISRY CIRCUIT 16SOIC |
| VE-JWB-EW-F4 | CONVERTER MOD DC/DC 95V 100W |
| LTC695ISW#PBF | IC MPU SUPERVISRY CIRCUIT 16SOIC |
| VE-JWB-EW-F3 | CONVERTER MOD DC/DC 95V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT375B | 制造商:EDSYN 功能描述:TIP SPADE 1.5X12.2MM |
| LT375-C | 制造商:EDSYN 功能描述: |
| LT376 | 制造商:EDSYN 功能描述: 制造商:EDSYN 功能描述:SOLDERING TIP, Tip / Nozzle Length:0.48" |
| LT3760 | 制造商:LINER 制造商全称:Linear Technology 功能描述:16-Channel 50mA LED |
| LT3760_12 | 制造商:LINER 制造商全称:Linear Technology 功能描述:8-Channel × 100mA LED Driver |
发布紧急采购，3分钟左右您将得到回复。