- 您现在的位置：买卖IC网 > PDF目录15253 > LT3781EG#TRPBF (Linear Technology)IC REG CTRLR ISO PWM CM 20-SSOP PDF资料下载
参数资料
| 型号： | LT3781EG#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 11/20页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR ISO PWM CM 20-SSOP |
| 标准包装： | 1,800 |
| PWM 型： | 电流模式 |
| 输出数： | 2 |
| 频率 - 最大： | 700kHz |
| 占空比： | 100% |
| 电源电压： | 8 V ~ 72 V |
| 降压： | 无 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 20-SSOP（0.209"，5.30mm 宽） |
| 包装： | 带卷 (TR) |
LT3781
APPLICATIO S I FOR ATIO
Events that trigger a GFC are:
a) Exceeding the current limit of the 5V REF pin
b) Detecting an undervoltage condition on V CC
c) Detecting an undervoltage condition on 5V REF
d) Pulling the SHDN pin below the shutdown threshold
e) Exceeding the 1.25V fault detector threshold on
either the OVLO or THERM pins
OVLO and THERM pins is used to directly trigger a GFC. If
either of these pins are not used, they can be disabled by
connecting the pin to ground. The intention of the OVLO
pin is to allow the monitoring of the input supply to protect
from an overvoltage condition though the use of a resistor
divider from the input supply. Monitoring of system tem-
perature (THERM) is possible through use of a resistor
divider using a thermistor as a divider component. The
5V REF pin can provide the precision supply required for
these applications. When these fault detection circuits are
disabled during shutdown or V CC pin UVLO conditions, a
reduction in OVLO and THERM pin input impedance to
ground will occur. To prevent excessive pin input currents,
low impedance pull-up devices must not be used on these
pins.
Undervoltage Lockout
The LT3781 maintains a low current operational mode
when an undervoltage condition is detected on the V CC
supply pin, or when V CC is below the undervoltage lockout
(UVLO) threshold. During a UVLO condition on the V CC
pin, the LT3781 disables all internal functions with the
the voltage across the bootstrap supply is greater than
7.4V. This helps prevent the possibility of forcing the high
side switch into a linear operational region, potentially
causing excessive power dissipation due to inadequate
gate drive during start-up.
Error Amplifer Configurations
The converter output voltage information is fed back to the
LT3781 onto the V FB pin where it is transformed into an
output current control voltage by the error amplifier. The
error amplifier is generally configured as an integrator and
is used to create the dominant pole for the main converter
feedback loop. The LT3781 error amplifier is a true high
gain voltage amplifier. The amplifier noninverting input is
internally referenced to 1.25V; the inverting input is the
V FB pin and the output is the V C pin. Because both low
frequency gain and integrator frequency characteristics
can be controlled with external components, this amplifier
allows far greater flexibility and precision compared with
use of a transconductance error amplifier.
In a nonisolated converter configuration where a resistor
divider is used to program the desired output voltage, the
error amplifier can be configured as a simple active
integrator, forming the system dominant pole ( Figure 1).
Placing a capacitor C ERR from the V FB pin to the V C pin will
set the single-pole crossover frequency at (2 π R FB C ERR ) -1 .
Additional poles and zeros can be added by increasing the
complexity of the RC network.
V OUT
R FB
exception of the shutdown and UVLO circuitry. The exter-
9
V FB
nal 5V REF supply is also disabled during this condition.
Disabling of all switching control circuity reduces the
LT3781 supply current to <1mA, making for efficient
C ERR
10
V C
integration of trickle charging in systems that employ
output feedback supply generation.
1.25V
The function of the high side switch output (TG) is also
gated by UVLO circuitry monitoring the bootstrap supply
LT3781
3781 F01
(V BST – BSTREF). Switching of the TG pin is disabled until
Figure 1. Nonisolated Error Amp Configuration
3781f
11
相关PDF资料 |
PDF描述 |
|---|---|
| LT3781EG#TR | IC REG CTRLR ISO PWM CM 20-SSOP |
| LTC1159IS#TRPBF | IC REG CTRLR BUCK PWM CM 16-SOIC |
| LTC1159IS-3.3#TRPBF | IC REG CTRLR BUCK PWM CM 16-SOIC |
| LTC1159IS-5#TRPBF | IC REG CTRLR BUCK PWM CM 16-SOIC |
| RGM15DRMN-S288 | CONN EDGECARD 30POS .156 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3781IG | 功能描述:IC REG CTRLR ISO PWM CM 20-SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,000 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:1MHz 占空比:50% 电源电压:9 V ~ 10 V 降压:无 升压:是 回扫:是 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 包装:带卷 (TR) |
| LT3781IG#PBF | 功能描述:IC REG CTRLR ISO PWM CM 20-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,000 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:1MHz 占空比:50% 电源电压:9 V ~ 10 V 降压:无 升压:是 回扫:是 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 包装:带卷 (TR) |
| LT3781IG#TR | 功能描述:IC REG CTRLR ISO PWM CM 20-SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LT3781IG#TRPBF | 功能描述:IC REG CTRLR ISO PWM CM 20-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LT3782 | 制造商:LINER 制造商全称:Linear Technology 功能描述:2-Phase Step-Up DC/DC Controller |
发布紧急采购，3分钟左右您将得到回复。