- 您现在的位置：买卖IC网 > PDF目录13987 > LT3971IMSE#TRPBF (Linear Technology)IC REG BUCK ADJ 1.2A 10MSOP PDF资料下载
参数资料
| 型号： | LT3971IMSE#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 12/28页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 1.2A 10MSOP |
| 标准包装： | 2,500 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 1.19 V ~ 30 V |
| 输入电压： | 4.3 V ~ 38 V |
| PWM 型： | 电流模式，Burst Mode? |
| 频率 - 开关： | 200kHz ~ 2MHz |
| 电流 - 输出： | 1.2A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 10-MSOP 裸露焊盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页当前第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LT3971/LT3971-3.3/LT3971-5
APPLICATIONS INFORMATION
Table 1. Switching Frequency vs R T Value
SWITCHING FREQUENCY (MHz)
R T VALUE (kΩ)
switch off-time. These equations show that duty cycle
range increases when switching frequency is decreased.
f SW(MAX) =
V IN(MIN) =
? V D + V SW
V IN(OP-MAX) =
– V D + V SW
0.2 255
0.4 118
0.6 71.5
0.8 49.9
1.0 35.7
1.2 28.0
1.4 22.1
1.6 17.4
1.8 14.0
2.0 11.0
Operating Frequency Tradeoffs
Selection of the operating frequency is a tradeoff between
efficiency, component size, minimum dropout voltage, and
maximum input voltage. The advantage of high frequency
operation is that smaller inductor and capacitor values may
be used. The disadvantages are lower efficiency, lower
maximum input voltage, and higher dropout voltage. The
highest acceptable switching frequency (f SW(MAX) ) for a
given application can be calculated as follows:
V OUT + V D
t ON(MIN) (V IN ? V SW + V D )
where V IN is the typical input voltage, V OUT is the output
voltage, V D is the catch diode drop (~0.5V), and V SW is
the internal switch drop (~0.5V at max load). This equation
shows that slower switching frequency is necessary to
safely accommodate high V IN /V OUT ratio. Also, as shown
in the Input Voltage Range section, lower frequency allows
a lower dropout voltage. The input voltage range depends
on the switching frequency because the LT3971 switch has
finite minimum on and off times. The minimum switch on
and off times are strong functions of temperature. Use
the typical minimum on and off curves to design for an
application’s maximum temperature, while adding about
30% for part-to-part variation. The minimum and maximum
duty cycles that can be achieved taking minimum on and
off times into account are:
DC MIN = f SW t ON(MIN)
DC MAX = 1 ? f SW t OFF(MIN)
where f SW is the switching frequency, the t ON(MIN) is the
minimum switch on-time, and the t OFF(MIN) is the minimum
A good choice of switching frequency should allow
adequate input voltage range (see Input Voltage Range
section) and keep the inductor and capacitor values small.
Input Voltage Range
The minimum input voltage is determined by either the
LT3971’s minimum operating voltage of 4.3V or by its
maximum duty cycle (see equation in Operating Frequency
Tradeoffs section). The minimum input voltage due to
duty cycle is:
V OUT + V D
1 ? f SW t OFF(MIN)
where V IN(MIN) is the minimum input voltage, V OUT is
the output voltage, V D is the catch diode drop (~0.5V),
V SW is the internal switch drop (~0.5V at max load), f SW
is the switching frequency (set by R T ), and t OFF(MIN) is
the minimum switch off-time. Note that higher switch-
ing frequency will increase the minimum input voltage.
If a lower dropout voltage is desired, a lower switching
frequency should be used.
The maximum input voltage for LT3971 applications
depends on switching frequency, the Absolute Maximum
Ratings of the V IN and BOOST pins, and the operating
mode. For a given application where the switching fre-
quency and the output voltage are already selected, the
maximum input voltage (V IN(OP-MAX) ) that guarantees
optimum output voltage ripple for that application can be
found by applying the following equation:
V OUT + V D
f SW ? t ON(MIN)
where t ON(MIN) is the minimum switch on-time. Note that
a higher switching frequency will decrease the maximum
operating input voltage. Conversely, a lower switching
frequency will be necessary to achieve normal operation
at higher input voltages.
The circuit will tolerate inputs above the maximum op-
erating input voltage and up to the Absolute Maximum
3971fd
12
相关PDF资料 |
PDF描述 |
|---|---|
| RSM22DRUI | CONN EDGECARD 44POS DIP .156 SLD |
| 10ZL100MEFC5X11 | CAP ALUM 100UF 10V 20% RADIAL |
| HM54-5BR51VLF | HIGH CURRENT TOROIDAL INDUCTORS |
| LT3971IDD#TRPBF | IC REG BUCK ADJ 1.2A 10DFN |
| HM72A-06100LFTR13 | INDUCTOR 10UH HI PWR/PERF SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3972 | 制造商:LINER 制造商全称:Linear Technology 功能描述:33V, 3.5A, 2.4MHz Step-Down Switching Regulator with 75μA Quiescent Current |
| LT3972EDD#PBF | 功能描述:IC REG BUCK ADJ 3.5A 10DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LT3972EDD#TRPBF | 功能描述:IC REG BUCK ADJ 3.5A 10DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT3972EDD-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:33V, 3.5A, 2.4MHz Step-Down Switching Regulator with 75μA Quiescent Current |
| LT3972EDD-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:33V, 3.5A, 2.4MHz Step-Down Switching Regulator with 75μA Quiescent Current |
发布紧急采购，3分钟左右您将得到回复。