参数资料
型号: LT3973EMSE-5#TRPBF
厂商: Linear Technology
文件页数: 9/24页
文件大小: 0K
描述: IC REG BUCK 5V 0.75A 10MSOP
标准包装: 2,500
类型: 降压(降压)
输出类型: 固定
输出数: 1
输出电压: 5V
输入电压: 4.2 V ~ 42 V
PWM 型: 电流模式,Burst Mode?
频率 - 开关: 195kHz ~ 2.15MHz
电流 - 输出: 750mA
同步整流器:
工作温度: -40°C ~ 125°C
安装类型: 表面贴装
封装/外壳: 10-TFSOP,10-MSOP(0.118",3.00mm 宽)裸露焊盘
包装: 带卷 (TR)
供应商设备封装: 10-MSOP 裸露焊盘
LT3973/LT3973-3.3/LT3973-5
PIN FUNCTIONS
FB (Pin 1, LT3973 Only): The LT3973 regulates the FB
pin to 1.21V. Connect the feedback resistor divider tap
to this pin.
V OUT (Pin 1, LT3973-3.3 and LT3973-5 Only): The
LT3973-3.3 and LT3973-5 regulate the V OUT pin to 3.3V
and 5V, respectively. This pin connects to the internal
feedback divider that programs the fixed output voltage.
OUT (Pin 2): The LT3973 regulates the V IN to V OUT voltage
for dropout conditions. It will also pull current from this
pin to charge the boost capacitor when needed. Connect
this pin to the output. If programmed output is greater
than 14V, tie this pin to GND.
EN/UVLO (Pin 3): The part is in shutdown when this pin is
low and active when this pin is high. The threshold voltage
is 1.19V going up with 30mV of hysteresis. Tie to V IN if
shutdown feature is not used. The EN/UVLO threshold is
accurate only when V IN is above 4.2V. If V IN is lower than
4.2V, ground EN/UVLO to place the part in shutdown.
GND (Pin 5, Exposed Pad Pin 11): Ground. The exposed
pad must be soldered to the PCB.
SW (Pin 6): The SW pin is the output of an internal power
switch. Connect this pin to the inductor.
BOOST (Pin 7): This pin is used to provide a drive volt-
age, higher than the input voltage, to the internal bipolar
NPN power switch.
BD (Pin 8): This pin connects to the anode of the boost
diode. This pin also supplies current to the LT3973’s internal
regulator when BD is above 3.2V.
PG (Pin 9): The PG pin is the open-drain output of an
internal comparator. PG remains low until the FB pin is
within 10% of the final regulation voltage. PG is valid when
V IN is above 4.2V and EN/UVLO is high.
RT (Pin 10): A resistor is tied between RT and ground to
set the switching frequency.
V IN (Pin 4): The V IN pin supplies current to the LT3973’s
internal circuitry and to the internal power switch. This
pin must be locally bypassed.
3973fa
9
相关PDF资料
PDF描述
V28C15C100BF2 CONVERTER MOD DC/DC 15V 100W
RBB34DHHN CONN EDGE DUAL .050 DIP 68 POS
RBB09DHAS CONN EDGECARD 18POS R/A .050 SLD
MAX6717AUKRFD6+T IC SUPERVISOR MPU SOT23-5
ESM06DTMT-S664 CONN EDGECARD 12POS R/A .156
相关代理商/技术参数
参数描述
LT3973EMSEPBF 制造商:Linear Technology 功能描述:42V 750mA Buck Regulator 2.5uA MSOP10EP
LT3973HDD#PBF 功能描述:IC REG BUCK ADJ 0.75A 10DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压(降压) 输出类型:固定 输出数:1 输出电压:1.2V,1.5V,1.8V,2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP,10-MSOP(0.118",3.00mm 宽)裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘
LT3973HDD#TRPBF 功能描述:IC REG BUCK ADJ 0.75A 10DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压(降压) 输出类型:固定 输出数:1 输出电压:1.2V,1.5V,1.8V,2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP,10-MSOP(0.118",3.00mm 宽)裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘
LT3973HDD-3.3#PBF 功能描述:IC REG BUCK 3.3V 0.75A 10DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压(降压) 输出类型:固定 输出数:1 输出电压:1.2V,1.5V,1.8V,2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP,10-MSOP(0.118",3.00mm 宽)裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘
LT3973HDD-3.3#TRPBF 功能描述:IC REG BUCK 3.3V 0.75A 10DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压(降压) 输出类型:固定 输出数:1 输出电压:1.2V,1.5V,1.8V,2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP,10-MSOP(0.118",3.00mm 宽)裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘