- 您现在的位置：买卖IC网 > PDF目录14021 > LT3990IDD#TRPBF (Linear Technology)IC REG BUCK ADJ 0.35A 10DFN PDF资料下载
参数资料
| 型号： | LT3990IDD#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 13/22页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 0.35A 10DFN |
| 标准包装： | 2,500 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 1.21 V ~ 25 V |
| 输入电压： | 4.2 V ~ 62 V |
| PWM 型： | 电流模式，Burst Mode? |
| 频率 - 开关： | 210kHz ~ 2.3MHz |
| 电流 - 输出： | 350mA |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-WFDFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 10-DFN（3x3） |
LT3990/LT3990-3.3/LT3990-5
APPLICATIONS INFORMATION
operates at a lower current limit during Burst Mode op-
eration, the noise is typically very quiet to a casual ear. If
this is unacceptable, use a high performance tantalum or
electrolytic capacitor at the output.
A final precaution regarding ceramic capacitors concerns
the maximum input voltage rating of the LT3990. As pre-
viously mentioned, a ceramic input capacitor combined
with trace or cable inductance forms a high quality (under
damped) tank circuit. If the LT3990 circuit is plugged into a
live supply, the input voltage can ring to twice its nominal
value, possibly exceeding the LT3990’s rating. This situation
is easily avoided (see the Hot Plugging Safely section).
500
400
300
200
100
0
0
FRONT PAGE APPLICATIO N
50 100 150 200 250
LOAD CURRENT (mA)
300 350
3990 F03
2μs/DIV
Low Ripple Burst Mode Operation
To enhance efficiency at light loads, the LT3990 operates
in low ripple Burst Mode operation which keeps the output
capacitor charged to the proper voltage while minimizing
the input quiescent current. During Burst Mode opera-
tion, the LT3990 delivers single cycle bursts of current to
the output capacitor followed by sleep periods where the
output power is delivered to the load by the output capaci-
tor. Because the LT3990 delivers power to the output with
single, low current pulses, the output ripple is kept below
5mV for a typical application. See Figure 2.
As the load current decreases towards a no load condition,
the percentage of time that the LT3990 operates in sleep
mode increases and the average input current is greatly
reduced resulting in high efficiency even at very low loads.
Note that during Burst Mode operation, the switching
frequency will be lower than the programmed switching
frequency. See Figure 3.
V SW
5V/DIV
I L
100mA/DIV
V OUT
5mV/DIV
3990 G28
FRONT PAGE APPLICATION
V IN = 12V
V OUT = 5V
I LOAD = 10mA
f = 600kHz
Figure 2. Burst Mode Operation
Figure 3. Switching Frequency in Burst Mode Operation
At higher output loads (above ~35mA for the front page
application) the LT3990 will be running at the frequency
programmed by the R T resistor, and will be operating in
standard PWM mode. The transition between PWM and
low ripple Burst Mode is seamless, and will not disturb
the output voltage.
BOOST and BD Pin Considerations
Capacitor C3 and the internal boost Schottky diode (see the
Block Diagram) are used to generate a boost voltage that
is higher than the input voltage. In most cases a 0.22μF
capacitor will work well. Figure 4 shows two ways to ar-
range the boost circuit. The BOOST pin must be more than
1.9V above the SW pin for best efficiency. For outputs of
2.2V and above, the standard circuit (Figure 4a) is best.
For outputs between 2.2V and 2.5V, use a 0.47μF boost
capacitor. For output voltages below 2.2V, the boost diode
can be tied to the input (Figure 4b), or to another external
supply greater than 2.2V. However, the circuit in Figure 4a
is more efficient because the BOOST pin current and BD
pin quiescent current come from a lower voltage source.
Also, be sure that the maximum voltage ratings of the
BOOST and BD pins are not exceeded.
The minimum operating voltage of an LT3990 application
is limited by the minimum input voltage (4.2V) and by the
maximum duty cycle as outlined in a previous section. For
proper start-up, the minimum input voltage is also limited
by the boost circuit. If the input voltage is ramped slowly,
the boost capacitor may not be fully charged. Because
3990fa
13
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6718AUKRFD3+T | IC SUPERVISOR MPU SOT23-5 |
| MAX6718AUKRFD5+T | IC SUPERVISOR MPU SOT23-5 |
| MAX6718AUKRFD2+T | IC SUPERVISOR MPU SOT23-5 |
| MAX6718AUKRDD5+T | IC SUPERVISOR MPU SOT23-5 |
| MAX6718AUKRVD1+T | IC SUPERVISOR MPU SOT23-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3990IMS | 制造商:LINER 制造商全称:Linear Technology 功能描述:60V, 350mA Step-Down Regulator with 2.5μA Quiescent Current and Integrated Diodes |
| LT3990IMSE#PBF | 功能描述:IC REG BUCK ADJ 0.35A 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT3990IMSE#TRPBF | 功能描述:IC REG BUCK ADJ 0.35A 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT3990IMSE-3.3#PBF | 功能描述:IC REG BUCK ADJ 0.35A 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:MIC23xxx HyperLight Load™ Regulators 标准包装:5,000 系列:HyperLight Load® 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.8V 输入电压:2.7 V ~ 5.5 V PWM 型:混合物 频率 - 开关:4MHz 电流 - 输出:2A 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘，8-MLF? 包装:带卷 (TR) 供应商设备封装:8-MLF?（2x2） 产品目录页面:1094 (CN2011-ZH PDF) 其它名称:576-3303-2 |
| LT3990IMSE-3.3#TRPBF | 功能描述:IC REG BUCK ADJ 0.35A 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
发布紧急采购，3分钟左右您将得到回复。