- 您现在的位置：买卖IC网 > PDF目录14816 > LT3991EMSE#PBF (Linear Technology)IC REG BUCK ADJ 1.2A 10MSOP PDF资料下载
参数资料
| 型号： | LT3991EMSE#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 13/24页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 1.2A 10MSOP |
| 标准包装： | 50 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 1.19 V ~ 30 V |
| 输入电压： | 4.3 V ~ 55 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 200kHz ~ 2MHz |
| 电流 - 输出： | 1.2A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 10-MSOP 裸露焊盘 |
| 产品目录页面： | 1332 (CN2011-ZH PDF) |
LT3991/LT3991-3.3/LT3991-5
APPLICATIONS INFORMATION
C OUT =
I D(AVG) = I OUT
13
InputCapacitor
Bypass the input of the LT3991 circuit with a ceramic
capacitor of X7R or X5R type. Y5V types have poor
performance over temperature and applied voltage, and
should not be used. A 4.7μF to 10μF ceramic capacitor
is adequate to bypass the LT3991 and will easily handle
the ripple current. Note that larger input capacitance is
required when a lower switching frequency is used (due
to longer on-times). If the input power source has high
impedance, or there is significant inductance due to
long wires or cables, additional bulk capacitance may be
necessary. This can be provided with a low performance
electrolytic capacitor.
Step-down regulators draw current from the input sup-
ply in pulses with very fast rise and fall times. The input
capacitor is required to reduce the resulting voltage
ripple at the LT3991 and to force this very high frequency
switching current into a tight local loop, minimizing EMI.
A 4.7μF capacitor is capable of this task, but only if it is
placed close to the LT3991 (see the PCB Layout section).
A second precaution regarding the ceramic input capacitor
concerns the maximum input voltage rating of the LT3991.
A ceramic input capacitor combined with trace or cable
inductance forms a high quality (under damped) tank cir-
cuit. If the LT3991 circuit is plugged into a live supply, the
input voltage can ring to twice its nominal value, possibly
exceeding the LT3991’s voltage rating. This situation is
easily avoided (see the Hot Plugging Safely section).
Output Capacitor and Output Ripple
The output capacitor has two essential functions. Along
with the inductor, it filters the square wave generated by the
LT3991 to produce the DC output. In this role it determines
the output ripple, so low impedance (at the switching
frequency) is important. The second function is to store
energy in order to satisfy transient loads and stabilize the
LT3991’s control loop. Ceramic capacitors have very low
equivalent series resistance (ESR) and provide the best
ripple performance. A good starting value is:
100
V OUT f SW
where f SW is in MHz, and C OUT is the recommended output
capacitance in μF. Use X5R or X7R types. This choice will
provide low output ripple and good transient response.
Transient performance can be improved with a higher
value capacitor. Increasing the output capacitance will
also decrease the output voltage ripple. A lower value of
output capacitor can be used to save space and cost but
transient performance will suffer.
When choosing a capacitor, look carefully through the
data sheet to find out what the actual capacitance is under
operating conditions (applied voltage and temperature). A
physically larger capacitor or one with a higher voltage rating
may be required. Table 3 lists several capacitor vendors.
Table 3. Recommended Ceramic Capacitor Vendors
MANUFACTURER WEBSITE
AVX www.avxcorp.com
Murata www.murata.com
Taiyo Yuden www.t-yuden.com
Vishay Siliconix www.vishay.com
TDK www.tdk.com
Catch Diode Selection
The catch diode (D1 from Block Diagram) conducts cur-
rent only during switch off time. Average forward current
in normal operation can be calculated from:
V IN – V OUT
V IN
where I OUT is the output load current. The only reason to
consider a diode with a larger current rating than necessary
for nominal operation is for the worst-case condition of
shorted output. The diode current will then increase to the
typical peak switch current. Peak reverse voltage is equal
to the regulator input voltage. Use a diode with a reverse
voltage rating greater than the input voltage.
3991fa
相关PDF资料 |
PDF描述 |
|---|---|
| VI-J50-EY-F2 | CONVERTER MOD DC/DC 5V 50W |
| HBC10DRAN-S734 | CONN EDGECARD 20POS .100 R/A PCB |
| MAX6419UK32+T | IC RESET MPU LOW PWR SOT23-5 |
| SLP222M100H3P3 | CAP ALUM 2200UF 100V 20% SNAP |
| HBC10DRAH-S734 | CONN EDGECARD 20POS .100 R/A PCB |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3991EMSETRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:55V, 1.2A Step-Down Regulator with 2.8 Quiescent Current |
| LT3991IDD#PBF | 功能描述:IC REG BUCK ADJ 1.2A 10DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:MIC23xxx HyperLight Load™ Regulators 标准包装:5,000 系列:HyperLight Load® 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.8V 输入电压:2.7 V ~ 5.5 V PWM 型:混合物 频率 - 开关:4MHz 电流 - 输出:2A 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘，8-MLF? 包装:带卷 (TR) 供应商设备封装:8-MLF?（2x2） 产品目录页面:1094 (CN2011-ZH PDF) 其它名称:576-3303-2 |
| LT3991IDD#TRPBF | 功能描述:IC REG BUCK ADJ 1.2A 10DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT3991IDDPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:55V, 1.2A Step-Down Regulator with 2.8 Quiescent Current |
| LT3991IDDTRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:55V, 1.2A Step-Down Regulator with 2.8 Quiescent Current |
发布紧急采购，3分钟左右您将得到回复。