- 您现在的位置：买卖IC网 > PDF目录14459 > LT3991IDD#PBF (Linear Technology)IC REG BUCK ADJ 1.2A 10DFN PDF资料下载
参数资料
| 型号： | LT3991IDD#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 18/24页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 1.2A 10DFN |
| 标准包装： | 121 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 1.19 V ~ 30 V |
| 输入电压： | 4.3 V ~ 55 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 200kHz ~ 2MHz |
| 电流 - 输出： | 1.2A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-WFDFN 裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 10-DFN（3x3） |
LT3991/LT3991-3.3/LT3991-5
APPLICATIONS INFORMATION
D4
MBRS140
V IN
V IN
BOOST
L1
V OUT
C2
EN
LT3991
SW
BD
V OUT
GND
FB
+
BACKUP
R PG
GND
3991 F07
Figure 8. Diode D4 Prevents a Shorted Input from Discharging a
Backup Battery Tied to the Output. It Also Protects the Circuit from
a Reversed Input. The LT3991 Runs Only When the Input is Present
PCB Layout
D1
C3
C1
C5
C4
R1
R T
R2
For proper operation and minimum EMI, care must be taken
during printed circuit board layout. Figure 9 shows the
recommended component placement with trace, ground
plane and via locations. Note that large, switched currents
flow in the LT3991’s V IN and SW pins, the catch diode
(D1), and the input capacitor (C1). The loop formed by
these components should be as small as possible. These
components, along with the inductor and output capacitor,
should be placed on the same side of the circuit board,
and their connections should be made on that layer. Place
a local, unbroken ground plane below these components.
The SW and BOOST nodes should be as small as possible.
Finally, keep the FB and R T nodes small so that the ground
traces will shield them from the SW and BOOST nodes.
The Exposed Pad on the bottom of the package must be
soldered to ground so that the pad acts as a heat sink. To
keep thermal resistance low, extend the ground plane as
much as possible, and add thermal vias under and near
the LT3991 to additional ground planes within the circuit
board and on the bottom side.
Hot Plugging Safely
The small size, robustness and low impedance of ceramic
capacitors make them an attractive option for the input
bypass capacitor of LT3991 circuits. However, these ca-
pacitors can cause problems if the LT3991 is plugged into
a live supply. The low loss ceramic capacitor, combined
with stray inductance in series with the power source,
forms an under damped tank circuit, and the voltage at
18
GND
3991 F09
VIAS TO LOCAL GROUND PLANE VIAS TO RUN/SS VIAS TO V IN
VIAS TO V OUT VIAS TO SYNC VIAS TO PG OUTLINE OF LOCAL
GROUND PLANE
Figure 9. A Good PCB Layout Ensures Proper, Low EMI Operation
the V IN pin of the LT3991 can ring to twice the nominal
input voltage, possibly exceeding the LT3991’s rating and
damaging the part. If the input supply is poorly controlled
or the user will be plugging the LT3991 into an energized
supply, the input network should be designed to prevent
this overshoot. See Linear Technology Application Note
88 for a complete discussion.
High Temperature Considerations
For higher ambient temperatures, care should be taken in
the layout of the PCB to ensure good heat sinking of the
LT3991. The Exposed Pad on the bottom of the package
must be soldered to a ground plane. This ground should be
tied to large copper layers below with thermal vias; these
layers will spread heat dissipated by the LT3991. Placing
additional vias can reduce thermal resistance further. The
maximum load current should be derated as the ambient
temperature approaches the maximum junction rating.
Power dissipation within the LT3991 can be estimated by
calculating the total power loss from an efficiency measure-
ment and subtracting the catch diode loss and inductor
3991fa
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3546EUFD#PBF | IC REG BUCK SYNC ADJ 1A/2A 28QFN |
| LTC1514IS8-5#PBF | IC REG MULTI CONFIG 5V 8SOIC |
| LT3510IFE#PBF | IC REG BUCK ADJ 2A DL 20TSSOP |
| VE-J2H-EX-B1 | CONVERTER MOD DC/DC 52V 75W |
| VE-J23-EX-B1 | CONVERTER MOD DC/DC 24V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3991IDDTRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:55V, 1.2A Step-Down Regulator with 2.8 Quiescent Current |
| LT3991IMSE#PBF | 功能描述:IC REG BUCK ADJ 1.2A 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT3991IMSE#TRPBF | 功能描述:IC REG BUCK ADJ 1.2A 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT3991IMSE-3.3#PBF | 功能描述:IC REG BUCK 3.3V 1.2A 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT3991IMSE-3.3#TRPBF | 功能描述:IC REG BUCK 3.3V 1.2A 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
发布紧急采购，3分钟左右您将得到回复。