- 您现在的位置：买卖IC网 > PDF目录79818 > LT4250HIN8#TRPBF (LINEAR TECHNOLOGY CORP) 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDIP8 PDF资料下载
参数资料
| 型号： | LT4250HIN8#TRPBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 电源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDIP8 |
| 封装： | 0.300 INCH, LEAD FREE, PLASTIC, DIP-8 |
| 文件页数： | 10/14页 |
| 文件大小： | 232K |
| 代理商： | LT4250HIN8#TRPBF |
LT4250L/LT4250H
5
4250lhfa
PIN FUNCTIONS
for this pin is 1.5μs. Add an external capacitor to this pin
for additional filtering.
VEE (Pin 4): Negative Supply Voltage Input. Connect to
the lower potential of the power supply.
SENSE (Pin 5): Circuit Breaker Sense Pin. With a sense
resistor placed in the supply path between VEE and SENSE,
the overcurrent condition will pull down the GATE pin and
regulate the voltage across the resistor to be 50mV. If
the overcurrent condition exists for more than 500μs the
electronic circuit breaker will trip and turnoff the external
MOSFET.
If the current limit value is set to twice the normal operating
current, only 25mV is dropped across the sense resistor
during normal operation. To disable the current limit feature,
VEE and SENSE can be shorted together.
GATE (Pin 6): Gate Drive Output for the External N-channel
MOSFET. The GATE pin will go high when the following
start-up conditions are met: the UV pin is high, the OV pin
is low, (VSENSE – VEE) < 50mV and the VDD pin is greater
than VUVLOH. The GATE pin is pulled high by a 45μA cur-
rent source and pulled low with a 50mA current source.
During current limit the GATE pin is pulled low using a
100mA current source.
DRAIN (Pin 7): Analog Drain Sense Input. Connect this
pin to the drain of the external N-channel MOSFET and
the V– pin of the power module. When the DRAIN pin is
below VDL, the PWRGD/PWRGD pin will latch to indicate
the switch is on.
VDD (Pin 8): Positive Supply Voltage Input. Connect this
pin to the higher potential of the power supply inputs and
the V+ pin of the power module. An undervoltage lockout
circuit disables the chip until the VDD pin is greater than
the 16V VUVLOH threshold.
PWRGD/PWRGD (Pin 1): Power Good Output Pin. This pin
will latch a power good indication when VDRAIN is within
VDL of VEE and VGATE is within VGH of ΔVGATE. This pin
can be connected directly to the enable pin of a power
module.
When the DRAIN pin of the LT4250L is above VEE by more
than VDL or VGATE is more than VGH from ΔVGATE, the
PWRGD pin will be high impedance, allowing the pull-up
current of the module’s enable pin to pull the pin high and
turn the module off. When VDRAIN drops below VDL and
VGATE rises above VGH, the PWRGD pin sinks current to
VEE, pulling the enable pin low and turning on the module.
This condition is latched until the GATE pin is turned off
via the UV, OV, UVLO or the electronic circuit breaker.
When the DRAIN pin of the LT4250H is above VEE by more
than VDL or VGATE is more than VGH from ΔVGATE, the
PWRGD pin will sink current to the DRAIN pin which pulls
the module’s enable pin low, forcing it off. When VDRAIN
drops below VDL and VGATE rises above VGH, the PWRGD
sink current is turned off, allowing the module’s pull-up
current to pull the enable pin high and turn on the module.
This condition is latched until the GATE pin is turned off
via the UV, OV, UVLO or the electronic circuit breaker.
OV (Pin 2): Analog Overvoltage Input. When OV is pulled
above the 1.255V threshold, an overvoltage condition is
detected and the GATE pin will be immediately pulled low.
The GATE pin will remain low until OV drops below the
1.235V threshold.
UV (Pin 3): Analog Undervoltage Input. When UV is pulled
below the 1.125V threshold, an undervoltage condition
is detected and the GATE pin will be immediately pulled
low. The GATE pin will remain low until UV rises above
the 1.255 threshold.
The UV pin is also used to reset the electronic circuit
breaker. If the UV pin is cycled low and high following the
trip of the circuit breaker, the circuit breaker is reset and a
normal power-up sequence will occur. The response time
相关PDF资料 |
PDF描述 |
|---|---|
| LTC6992CDCB6-3#PBF | SWITCHING CONTROLLER, PDSO6 |
| LM4041CIZ-ADJAMMOPACK | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 1.233 V, PBCY3 |
| LS2660-9EPD3TB1 | 2-OUTPUT 100 W AC-DC REG PWR SUPPLY MODULE |
| LS2660-9EPD4T | 2-OUTPUT 100 W AC-DC REG PWR SUPPLY MODULE |
| LS2660-9EPD6TB1 | 2-OUTPUT 100 W AC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT4250HIS8 | 功能描述:IC CONTRLR HOTSWAP NEG 48V 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| LT4250HIS8#PBF | 功能描述:IC CONTRLR HOTSWAP NEG 48V 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| LT4250HIS8#TR | 功能描述:IC CONTRLR HOTSWAP NEG 48V 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| LT4250HIS8#TRPBF | 功能描述:IC CONTRLR HOTSWAP NEG 48V 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| LT4250L | 制造商:LINER 制造商全称:Linear Technology 功能描述:Negative 48V Hot Swap Controller |
发布紧急采购，3分钟左右您将得到回复。