- 您现在的位置：买卖IC网 > PDF目录19877 > LT4250HIS8#TR (Linear Technology)IC CONTRLR HOTSWAP NEG 48V 8SOIC PDF资料下载
参数资料
| 型号： | LT4250HIS8#TR |
| 厂商： | Linear Technology |
| 文件页数： | 9/14页 |
| 文件大小： | 236K |
| 描述： | IC CONTRLR HOTSWAP NEG 48V 8SOIC |
| 标准包装： | 2,500 |
| 类型： | 热交换控制器 |
| 应用： | 通用 |
| 内部开关： | 无 |
| 电源电压： | -20 V ~ -80 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 带卷 (TR) |
| 其它名称： | LT4250HIS8TR |
LT4250L/LT4250H
9
4250lhfa
DRAIN voltage has finished ramping, the GATE pin then
ramps to its final value.
Current Limit/Electronic Circuit Breaker
The LT4250 features a current limit function that protects
against short circuits or excessive supply currents. If the
current limit is active for more than 500約 the electronic
circuit breaker will trip. By placing a sense resistor between
the V
EE
and SENSE pin, the current limit will be activated
whenever the voltage across the sense resistor is greater
than 50mV .
Note that the current limit threshold should be set suffi-
ciently high to account for the sum of the load current
and the inrush current. The maximum value of the inrush
current is given by:
I
INRUSH
0.8"
40mV
R
SENS
E
I
LOAD,
where the 0.8 factor is used as a worst case margin com-
bined with the minimum trip voltage (40mV).
In the case of a short circuit, the current limit circuitry
activates and immediately pulls the GATE low, servos the
SENSE voltage to 50mV , and starts a 500約 timer. The
MOSFET current is limited to 50mV/R
SENSE
(see Figure 7).
If the short circuit persists for more than 500約, the circuit
breaker trips and pulls the GATE pin low, shutting off the
MOSFET . The circuit breaker is reset by pulling UV low,
or by cycling power to the part. If the short circuit clears
before the 500約 timing interval the current limit will
deactivate and release the GATE.
APPLICATIONS INFORMATION
Figure 7. Short-Circuit Protection Waveforms
DRAIN
50V/DIV
GATE
10V/DIV
I
D
(Q1)
5A/DIV
1ms/DIV
The LT4250 guards against voltage steps on the input
supply. A positive voltage step (increasing in magnitude)
on the input supply causes an inrush current that is
proportional to the voltage slew rate I = C
L
" 擵/擳 . If the
inrush exceeds 50mV/R
SENSE
, the current limit will activate
as shown in Figure 8. The GATE pin pulls low, limiting the
current to 50mV/R
SENSE
. At this level the MOSFET drain
will not follow the source as the input voltage rapidly
changes, but instead remains at the voltage stored on the
load capacitance. The load capacitance begins to charge
at a current of 50mV/R
SENSE
, but not for long. As the load
capacitance charges, C2 pushes back on the gate and limits
the MOSFET current in a manner identical to the initial start-
up condition which is less than the short circuit limiting
value of 50mV/R
SENSE
. Thus the circuit breaker does not
trip. To ensure correct operation under input voltage step
conditions, R
SENSE
must be chosen to provide a current
limit value greater than the sum of the load current and
the dynamic current in the load capacitance.
For C2 values less than 10nF a positive voltage step
increasing in magnitude on the input supply can result
in the Q1 turning off momentarily due to current limit
overshoot which can shut down the output. By adding an
additional resistor and diode, Q1 remains on during the
voltage step. This is shown as D1 and R7 in Figure 9. The
purpose of D1 is to shunt current around R7 when the
power pins first make contact and allow C1 to hold the
GATE low. The value of R7 should be sized to generate an
R7 " C1 time constant of 33約.
Under some conditions, a short circuit at the output can
cause the input supply to dip below the UV threshold. The
LT4250 turns off once and then turns on until the electronic
circuit breaker is tripped. This can be minimized by adding
a deglitching delay to the UV pin with a capacitor from UV
to V
EE
. This capacitor forms an RC time constant with the
resistors at UV , allowing the input supply to recover before
the UV pin resets the circuit breaker.
相关PDF资料 |
PDF描述 |
|---|---|
| VI-212-CY-F1 | CONVERTER MOD DC/DC 15V 50W |
| F152K43Y5RN63J5R | CAP CER 1500PF 1KV 10% RADIAL |
| V150C5H100B | CONVERTER MOD DC/DC 5V 100W |
| R0.5Z-2405/H | CONV DC/DC 0.5W 24VIN 05VOUT |
| T97H337M020EBA | CAP TANT 330UF 20V 20% 3226 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT4250L | 制造商:LINER 制造商全称:Linear Technology 功能描述:Negative 48V Hot Swap Controller |
| LT4250LCN8 | 功能描述:IC CONTRLR HOT SWAP NEG 48V 8DIP RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
| LT4250LCN8#PBF | 功能描述:IC CONTRLR HOT SWAP NEG 48V 8DIP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
| LT4250LCS8 | 功能描述:IC CONTRLR HOTSWAP NEG 48V 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| LT4250LCS8#PBF | 功能描述:IC CONTRLR HOTSWAP NEG 48V 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。