- 您现在的位置：买卖IC网 > PDF目录7413 > LT4H-AC240VS (Panasonic Electric Works)TIMER RELAY DIGITAL 240VAC SCREW PDF资料下载
参数资料
| 型号： | LT4H-AC240VS |
| 厂商： | Panasonic Electric Works |
| 文件页数： | 14/16页 |
| 文件大小： | 0K |
| 描述： | TIMER RELAY DIGITAL 240VAC SCREW |
| 产品目录绘图： | LT4H Series LT4H Series Part Names LT4H Series Schmatic |
| 特色产品： | Digital and Analog Timers |
| 标准包装： | 1 |
| 系列： | LT4H |
| 继电器类型： | 集成式 |
| 功能： | 可编程（多功能） |
| 电路： | SPDT（1 C 型） |
| 延迟时间： | 0.001 秒 999.9 小时 |
| 输出类型： | 机械式继电器 |
| 触点额定电压： | 5A @ 250VAC |
| 电源电压： | 100 ~ 240VAC |
| 安装类型： | 面板安装 |
| 端接类型： | 螺丝端子 |
| 计时调节方法： | 上行/下行数字键 |
| 计时启动方法： | 输入电压 |
| 产品目录页面： | 2864 (CN2011-ZH PDF) |
| 其它名称： | 255-1215 |
PRECAUTIONS IN USING THE LT4H SERIES
1. Terminal wiring
1) When wiring the terminals, refer to the
terminal layout and wiring diagrams and
be sure to perform the wiring properly
If independent power circuitry must be
used, keep the input contacts or transis-
tors separate from each other, as shown
in Fig. B.
Reset input
Start input
Stop input
Lock
input
without errors.
2) When using the instrument with an
flush mounting, the screw-down terminal
type is recommended. For the pin type,
use either the rear terminal block
(Fig. B)
Input contact
point or transistor
3
Input
terminal
8-pin type
11-pin type
Screw terminal type
1
3
6
—
4
7
—
5
8
4
6
9
3
7
10
(AT78041) or the 8P cap (AD8-RC) for
the 8-pin type, and the rear terminal
block (AT78051) or the 11P cap (AT8-
DP11) for the 11-pin type. Avoid solder-
ing directly to the round pins on the unit.
Input contact
point or transistor
3
2
10
Input
terminal
Power
supply
* The short-circuit impedance should be
less than 1 k ? .
[When the impedance is 0 ? , the current
coming from the start input and stop
When using the instrument with a front
panel installation, use the DIN rail termi-
2
10
input terminals is approximately 12 mA,
and from the reset input and lock input
nal block (AT8-DF8K) for the 8-pin type
and the DIN rail terminal block (AT8-
DF11K) for the 11-pin type.
3) After turning the unit off, make sure
that any resulting induced voltage or
residual voltage is not applied to power
supply terminals W through U (8-pin
When power circuitry is not independent,
one input signal can be fed to two or
more counters at once, as shown in Fig.
C.
(Fig. C)
Input contact
point or transistor
terminals is approximately 1.5 mA.]
Also, the open-circuit impedance should
be more than 100 k ? .
* As shown in the diagram below, from a
non-contact point circuit (proximity
type) W through P (11-pin type) or 1
and 2 (screw terminal type). (If the
3
Input
terminal
switches, photoelectric switches, etc.)
with a power supply voltage of between
power supply wire is wired parallel to the
high voltage wire or power wire, an
2
10
Power
supply
12 and 40 V, the signal can be input
without using an open collector transis-
induced voltage may be generated
between the power supply terminals.)
tor. In the case of the diagram below,
when the non-contact point transistor Q
4) Have the power supply voltage pass
through a switch or relay so that it is
3
2
Input
terminal
10
switches from off to on (when the signal
voltage goes from high to low), the sig-
applied at one time. If the power supply
nal is input.
is applied gradually, the counting may
malfunction regardless of the settings,
the power supply reset may not function,
or other such unpredictable occurrence
may result.
2. Input connections
The power circuit has no transformer
(power and input terminals are not insu-
lated). When an input signal is fed to two
or more timers at once, do not arrange
3. Input and output
1) Signal input type
(1) Contact point input
Use highly reliable metal plated contacts.
Since the contact point’s bounce time
leads directly to error in the timer opera-
tions, use contacts with as short a
bounce time as possible. Also, select a
minimum input signal width of 20 ms.
12 to 40V DC
Reset input
Q
8-pin type 1 — —
11-pin type 3 4 5
Screw terminal type 6 7 8
(The above example is for reset input)
4
6
9
3
7
10
the power circuit in an independent way.
If the timer is powered on and off inde-
pendently as shown in Fig. A, the timer's
internal circuitry may get damaged.Be
careful never to allow such circuitry.
Reset input
Start input
Stop input
Lock
input
2) The input mode and output mode
change depending on the DIP switch set-
tings. Therefore, before making any con-
nections, be sure to confirm the opera-
tion mode and operation conditions cur-
(Figs. A, B and C show the circuitry for
the 11-pin type.)
(Fig. A)
Input contact
8-pin type
11-pin type
Screw terminal type
1
3
6
—
4
7
—
5
8
4
6
9
3
7
10
rently set.
3) The LT4H series use power supply
without a transformer (power and input
terminals are not insulated). In connect-
point or transistor
3
3
2
Input
terminal
10
Input
terminal
Power
supply
(2) Non-contact point input
Connect with an open collector. Use
transistors whose characteristics satisfy
the criteria given below.
V CEO = 20 V min.
I C = 20 mA min.
I CBO = 6μA max.
Also, use transistors with a residual volt-
ing various kinds of input signals, there-
fore, use a power transformer in which
the primary side is separated from the
ungrounded secondary side as shown in
Fig. A, for the power supply for a sensor
and other input devices so that short-cir-
cuiting can be prevented.
2
10
age of less than 2 V when the transistor
is on.
47
相关PDF资料 |
PDF描述 |
|---|---|
| 3-1546159-4 | CONN BARRIER BLOCK 17CIRC 9.53MM |
| 4301.1403 | FUSE DRWR FOR PWR MOD X-SAFE 2PL |
| 4-1437648-9 | CONN BARRIER BLOCK 23CIRC 8.26MM |
| 3M 4905 0.75"SQ-250 | 3M 4905 VHB 3/4" SQ -250/PACK |
| 2-1546399-3 | CONN BARRIER BLOCK 18CIRC 9.53MM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT4H-AC24V | 制造商:PANASONIC ELECTRIC WORKS ACSD 功能描述:Timer, Digital, LT4H, 24 VAC, DIN48, 2 Color LCD, 8 Modes |
| LT4H-DC24V | 功能描述:计时器 24VDC OCT 11 PIN RoHS:否 制造商:Omron Industrial 定时范围:0.05 s to 30 hr 电源电压:100 VAC to 240 VAC 系列: |
| LT4H-DC24VS | 功能描述:计时器 24VDC SCREW TERM RoHS:否 制造商:Omron Industrial 定时范围:0.05 s to 30 hr 电源电压:100 VAC to 240 VAC 系列: |
| LT4HL8-AC240V | 制造商:Panasonic Electric Works 功能描述:LT4H(LOW COST) DIGITAL TIMER, 8-PIN, 240VAC, RELAY-OUTPUT, DIN48,IP66 |
| LT4HL8-AC24V | 功能描述:Programmable (Multi-Function) Time Delay Relay SPDT (1 Form C) 0.001 Sec ~ 999.9 Hrs Delay 5A @ 250VAC Socket 制造商:panasonic industrial automation sales 系列:LT4H-L 零件状态:有效 继电器类型:集成式 功能:可编程（多功能） 电路:SPDT（1 C 形） 延迟时间:0.001 秒 999.9 小时 输出类型:机械式继电器 不同电压时的触头额定电流:5A @ 250VAC 电压 - 电源:24VAC/DC 安装类型:插口 端子类型:8 引脚可插 定时调节方法:上行/下行数字键 定时启动方法:输入电压 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。