- 您现在的位置：买卖IC网 > Datasheet目录988 > LT4HW-DC24VS (Panasonic Electric Works)TIMER DIGITAL 24VDC SCREW TERM Datasheet资料下载
参数资料
| 型号： | LT4HW-DC24VS |
| 厂商： | Panasonic Electric Works |
| 文件页数： | 15/16页 |
| 文件大小： | 0K |
| 描述： | TIMER DIGITAL 24VDC SCREW TERM |
| 标准包装： | 1 |
| 系列： | LT4H-W |
| 继电器类型： | 集成式 |
| 功能： | 可编程（多功能） |
| 电路： | SPDT（1 C 型） |
| 延迟时间： | 0.1 秒 ~ 9999 小时 |
| 输出类型： | 机械式继电器 |
| 触点额定电压： | 5A @ 250VAC |
| 电源电压： | 12 ~ 24VDC |
| 安装类型： | 面板安装 |
| 端接类型： | 螺丝端子 |
| 计时调节方法： | 上行/下行数字键 |
| 计时启动方法： | 输入电压 |
| 其它名称： | Q1140702 |
PRECAUTIONS IN USING THE LT4H SERIES
Once the wiring to be used is completely
installed and prior to installing this timer,
(2) Use the diode connected to the out-
put transistor’s collector for absorbing
? Surge wave form
[± (1.2 × 50) μs uni-polar full wave voltage]
confirm that there is complete insulation
between the wires connected to the
power terminals (2 each) and the wires
connected to each input terminal. If the
the reverse voltage from induced loads.
LT4H timer
100
90
Peak
power and input lines are not insulated, a
short-circuit may occur inside the timer
Inductive load
50
30
and result in internal damage.
In addition, when moving your equipment
to a new installation location, confirm
Diode rating:
I F (forward current): 1 A
V R (reverse voltage): 600 V
Load’s
power supply
0
0
1.2
Time ( μ s)
50
that there is no difference in environmen-
tal conditions as compared to the previ-
ous location.
(Fig. A) Good example
AC power supply
Insulation transformer
6) When wiring, use shielded wires or
metallic wire tubes, and keep the wire
lengths as short as possible.
7) For the load of the controlled output,
make sure that it is lower than the rated
4) Regarding external noise, the values
below are considered the noise-resistant
voltages. If voltages rise above these
values, malfunctions or damage to the
internal circuitry may result, so take the
(+)
(–)
Input device
(e.g., sensor)
control capacity.
necessary precautions.
(–)
Timer
(Fig. B) Bad example
AC power supply
Insulation transformer
(+)
(–)
(–)
Timer
Input device
(e.g., sensor)
4. Operation of LT4H digital timer
1) Turning on and off the power supply
while operating in A2* (Power on delay
2) or G (Totalizing On delay) will result in
a timer error to be generated due to the
characteristics of the internal circuitry.
Therefore, use the start input or stop
input.
* Not related to the start input.
2) When controlling the timer by turning
Power supply terminals
DC type
AC type
24V AC type
Noise
1,500V 1,000V
voltage
Noise wave form (noise simulator)
Rise time: 1 ns
Pulse width: 1 μs, 50 ns
Polarity: ±
Cycle: 100 cycles/second
Input
terminals
600V
AC power supply
Single coil transformer
on the power supply, use only A (Power
on delay 1) or A2 (Power on delay 2).
5) When connecting the operating power
supply, make sure that no leakage cur-
Timer
(+)
(–)
Input device
(e.g., sensor)
(–)
Alternative
current flow
Use of other modes in this situation will
result in timer errors. When using the
other modes, control the timer with the
start input or stop input.
5. Operation mode and time range set-
rent enters the timer. For example, when
performing contact protection, if set up
like that of fig. A, leaking current will
pass through C and R, enter the unit,
and cause incorrect operation. The fig. B
R
C
4) The input signal is applied by the
shorting of each input terminal with the
common terminal (terminal Q for 8-pin
types, terminal E for 11-pin types and
terminal 6 for screw terminal types).
Never connect other terminals or volt-
ages higher than 40V DC, because it
may destroy the internal circuitry.
5) Transistor output
(1) Since the transistor output is insulat-
ed from the internal circuitry by a pho-
tocoupler, it can be used as an NPN
output or PNP (equal value) output.
(The above example is 11-pin type)
ting
The operation mode and time range can
be set with the DIP switches on the side
of the timer. Make the DIP switch set-
tings before installing the timer on the
panel.
The operation mode of LT4H-W series
can be set with the keys and switches on
the front of the timer.
6. Conditions of usage
1) Avoid locations subject to flammable
or corrosive gases, excessive dust, oil,
vibrations, or excessive shocks.
2) Since the cover of the timer is made of
polycarbonate resin, avoid contact with
shows the correct setup.
Leakage current
Operating power supply
(Fig. A)
R
T
As NPN output
LT4H timer
or use in environments containing methyl
alcohol, benzene, thinners, and other
Operating power supply
T
{
O
I
organic solvents; and ammonia, caustic
C
sodas, and other alkaline substances.
Load
Load’s power supply
3) If power supply surges exceed the val-
ues given below, the internal circuits may
become damaged. Be sure to use surge
absorbing element to prevent this from
(Fig. B)
As PNP output
LT4H timer
happening.
{
Load
O
I
Operating voltage Surge voltage (peak value)
AC type
6,000V
DC type
1,000V
24V AC type
Load’s power supply
Note: With the 8-pin type, there is no diode
between points I and O .
48
相关PDF资料 |
PDF描述 |
|---|---|
| LTR18EZPJ910 | RES 91 OHM 1/2W 5% 1206 WIDE |
| LTR50UZPJ391 | RES 390 OHM 1W 5% 2010 WIDE |
| LVD75F100H | RELAY SSR LOWVOL DIS 26.6V 100A |
| LVK20R010DER | RES .01 OHM 3/4W .5% 2010 SMD |
| RW-2405S/SMD | DC/DC转换器 3W DC/DC MIN 1kV REG 2:1 18-36Vin 5Vout |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT4HWT8-AC240V | 制造商:Panasonic Electric Works 功能描述: |
| LT4HWT8-AC24V | 制造商:Panasonic Electric Works 功能描述: |
| LT4HWT-AC240VS | 制造商:Panasonic Electric Works 功能描述:Timer, Transistor Output, Screw Connect, IP66 |
| LT4HWT-AC24V | 制造商:Panasonic Electric Works 功能描述: |
| LT4HWT-AC24VS | 制造商:Panasonic Electric Works 功能描述:Digital Timer, 24VDC, 11-Pin Terminal |
发布紧急采购，3分钟左右您将得到回复。