参数资料
| 型号： | LT6000IDCB#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 3/20页 |
| 文件大小： | 0K |
| 描述： | IC OP AMP R-R 1.8V 6-DFN |
| 标准包装： | 2,500 |
| 放大器类型： | 通用 |
| 电路数： | 1 |
| 输出类型： | 满摆幅 |
| 转换速率： | 0.018 V/µs |
| 增益带宽积： | 60kHz |
| 电流 - 输入偏压： | 4nA |
| 电压 - 输入偏移： | 500µV |
| 电流 - 电源： | 20µA |
| 电流 - 输出 / 通道： | 10mA |
| 电压 - 电源，单路/双路(±)： | 1.8 V ~ 16 V，±0.9 V ~ 8 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 6-WFDFN 裸露焊盘 |
| 供应商设备封装： | 6-DFN-EP（2x3） |
| 包装： | 带卷 (TR) |
LT6000/LT6001/LT6002
11
600012fa
Q1
Q17
Q6
Q2
Q10
C1
Q3
IN+
Q8
Q19
Q20
R1
R8
7M
R6
R7
R2
30k
D3
V+
V–
R4
R5
IN–
R3
30k
Q9
Q11
Q14
V+
OUT
V–
SHDN
V–
Q15
CM
Q13
COMPLEMENTARY
DRIVE GENERATOR
Q12
Q4
Q5
Q7
Q16
Q18
APPLICATIO S I FOR ATIO
WU
UU
Supply Voltage
The positive supply of the LT6000/LT6001/LT6002 should
be bypassed with a small capacitor (about 0.01
F) within
an inch of the pin. When driving heavy loads, an additional
4.7
F electrolytic capacitor should be used. When using
split supplies, the same is true for the negative supply pin.
Rail-to-Rail Characteristics
The LT6000/LT6001/LT6002 are fully functional for an
input signal range from the negative supply to the positive
supply. Figure 1 shows a simplified schematic of the
amplifier. The input stage consists of two differential
amplifiers, a PNP stage Q3/Q6 and an NPN stage Q4/Q5
that are active over different ranges of the input common
mode voltage. The PNP stage is active for common mode
voltages, VCM, between the negative supply to approxi-
mately 1V below the positive supply. As VCM moves closer
towards the positive supply, the transistor Q7 will steer
Q2’s tail current to the current mirror Q8/Q9, activating the
NPN differential pair. The PNP pair becomes inactive for
the rest of the input common mode range up to the
positive supply.
The second stage is a folded cascode and current mirror
that converts the input stage differential signals into a
single ended output. Capacitor C1 reduces the unity cross
frequency and improves the frequency stability without
degrading the gain bandwidth of the amplifier. The comple-
mentary drive generator supplies current to the output
transistors that swing from rail to rail.
Input
The input bias current depends on which stage is active.
The input bias current polarity depends on the input
common mode voltage. When the PNP stage is active, the
input bias currents flow out of the input pins. They flow in
the opposite direction when the NPN stage is active. The
offset error due to the input bias currents can be
minimized by equalizing the noninverting and inverting
source impedance.
Figure 1
SI PLIFIED SCHE ATIC
WW
相关PDF资料 |
PDF描述 |
|---|---|
| AGC-V-1/10-R | FUSE 1/10A 250V GLS FST AXIAL UL |
| MDL-1/16-R | FUSE 1/16A 250V T-LAG GLASS |
| MDL-1/10-R | FUSE 1/10A 250V T-LAG GLASS |
| 31159 | CONN RING TONGUE 22-16AWG #6 |
| RL0816S-680-F | RES 68 OHM 1/5W 1% 0603 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT6001 | 制造商:Pulse 功能描述:- Bulk |
| LT6001CDD | 制造商:Linear Technology 功能描述:OP Amp Dual GP R-R I/O 18V 10-Pin DFN EP |
| LT6001CDD#PBF | 功能描述:IC OP AMP R-R DUAL 10-DFN RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:2,500 系列:- 放大器类型:通用 电路数:1 输出类型:满摆幅 转换速率:0.11 V/µs 增益带宽积:350kHz -3db带宽:- 电流 - 输入偏压:4nA 电压 - 输入偏移:20µV 电流 - 电源:260µA 电流 - 输出 / 通道:20mA 电压 - 电源，单路/双路(±):2.7 V ~ 36 V，±1.35 V ~ 18 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SO 包装:带卷 (TR) |
| LT6001CDD#TRPBF | 功能描述:IC OP AMP DUAL R-R 10-DFN RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:2,500 系列:- 放大器类型:通用 电路数:1 输出类型:满摆幅 转换速率:0.11 V/µs 增益带宽积:350kHz -3db带宽:- 电流 - 输入偏压:4nA 电压 - 输入偏移:20µV 电流 - 电源:260µA 电流 - 输出 / 通道:20mA 电压 - 电源，单路/双路(±):2.7 V ~ 36 V，±1.35 V ~ 18 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SO 包装:带卷 (TR) |
| LT6001CMS8 | 制造商:Linear Technology 功能描述:OP Amp Dual GP R-R I/O 18V 8-Pin MSOP |
发布紧急采购，3分钟左右您将得到回复。