参数资料
| 型号： | LT6002IDHC#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 4/20页 |
| 文件大小： | 0K |
| 描述： | IC OP AMP R-R 1.8V QUAD 16-DFN |
| 标准包装： | 73 |
| 放大器类型： | 通用 |
| 电路数： | 4 |
| 输出类型： | 满摆幅 |
| 转换速率： | 0.018 V/µs |
| 增益带宽积： | 60kHz |
| 电流 - 输入偏压： | 4nA |
| 电压 - 输入偏移： | 500µV |
| 电流 - 电源： | 20µA |
| 电流 - 输出 / 通道： | 10mA |
| 电压 - 电源，单路/双路(±)： | 1.8 V ~ 16 V，±0.9 V ~ 8 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-WFDFN 裸露焊盘 |
| 供应商设备封装： | 16-DFN（5x3） |
| 包装： | 管件 |
LT6000/LT6001/LT6002
600012fa
12
APPLICATIO S I FOR ATIO
WU
UU
The input offset voltage changes depending on which
input stage is active; input offset voltage is trimmed on
both input stages, and is guaranteed to be 600
V max in
the PNP stage. By trimming the input offset voltage of
both input stages, the input offset voltage over the entire
common mode range (CMRR) is typically 400
V, main-
taining the precision characteristics of the amplifier.
The input stage of the LT6000/LT6001/LT6002 incorpo-
rates phase reversal protection to prevent wrong polarity
outputs from occurring when the inputs are driven up to
2V below the negative rail. 30k protective resistors are
included in the input leads so that current does not
become excessive when the inputs are forced below V– or
when a large differential signal is applied. Input current
should be limited to 10mA when the inputs are driven
above the positive rail.
Output
The output of the LT6000/LT6001/LT6002 can swing to
within 30mV of the positive rail with no load and within
30mV of the negative rail with no load. When monitoring
input voltages within 30mV of the positive rail or within
30mV of the negative rail, gain should be taken to keep
the output from clipping. The LT6000/LT6001/LT6002
can typically source 10mA on a single 5V supply, sourc-
ing current is reduced to 4mA on a single 1.8V supply as
noted in the electrical characteristics.
The normally reverse-biased substrate diode from the
output to V– will cause unlimited currents to flow when the
output is forced below V–. If the current is transient and
limited to 100mA, no damage will occur.
Start-Up and Output Saturation Characteristics
Micropower op amps are often not micropower during
start-up characteristics or during output saturation. This
can wreak havoc on limited current supplies, in the worst
case there may not be enough supply current available to
take the system up to nominal voltages. Also, when the
output saturates, the part may draw excessive current and
pull down the supplies, compromising rail-to-rail perfor-
mance. Figure 1 shows the start-up characteristics of the
LT6000/LT6001/LT6002 for three limiting cases. The cir-
cuits are shown in Figure 2. One circuit creates a positive
offset forcing the output to come up saturated high.
Another circuit creates a negative offset forcing the output
to come up saturated low, while the last circuit brings the
output up at 1/2 supply. In all cases, the supply current is
well controlled and is not excessive when the output is on
either rail.
SUPPLY VOLTAGE (V)
0
SUPPLY
CURRENT
PER
AMPLIFIER
(
A)
12
16
20
4
60012 F01
8
4
10
14
18
6
2
0
1
0.5
2
1.5
3
3.5
4.5
2.5
5
OUTPUT LOW
OUTPUT HIGH
OUTPUT AT VS/2
–
+
30mV
VS
Output High
–
+
VS/2
VS
60012 F02
Output at VS/2
–
+
30mV
VS
Output Low
Figure 1. Start-Up Characteristics
Figure 2. Circuits for Start-Up Characteristics
相关PDF资料 |
PDF描述 |
|---|---|
| 5-147105-6 | 12 MODIV VRT DR SFMNT 30AU |
| 7-917570-1 | 1.5 B-T-W HDR ASSY 11P W/O BOS |
| 1-535598-3 | CONN RCPT 26POS .100 DUAL T/H AU |
| 1-535542-1 | CONN RECEPT 22POS .100 VERT DUAL |
| 5-534236-8 | CONN RCPT 16POS .100 DL T/H GOLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT6002IGN | 制造商:LINER 制造商全称:Linear Technology 功能描述:Single, Dual and Quad, 1.8V, 13uA Precision Rail-to-Rail Op Amps |
| LT6002IGN#PBF | 功能描述:IC OP AMP R-R 1.8V QUAD 16-SSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 其它有关文件:Automotive Product Guide 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 放大器类型:通用 电路数:1 输出类型:满摆幅 转换速率:3 V/µs 增益带宽积:10MHz -3db带宽:- 电流 - 输入偏压:1pA 电压 - 输入偏移:70µV 电流 - 电源:2.5mA 电流 - 输出 / 通道:48mA 电压 - 电源，单路/双路(±):2.7 V ~ 5.5 V，±1.35 V ~ 2.75 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:Digi-Reel® 其它名称:MAX4475AUT#TG16DKR |
| LT6002IGN#TRPBF | 功能描述:IC OP AMP R-R 1.8V QUAD 16-SSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 放大器类型:电流检测 电路数:1 输出类型:- 转换速率:- 增益带宽积:125kHz -3db带宽:- 电流 - 输入偏压:- 电压 - 输入偏移:100µV 电流 - 电源:1.1µA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:4-WFBGA，CSPBGA 供应商设备封装:4-UCSP（2x2） 包装:剪切带 (CT) 其它名称:MAX9634WERS+TCT |
| LT6003 | 功能描述:变压器音频和信号 ETHERNET AUI XFMR RoHS:否 制造商:Skyworks Solutions, Inc. 频率范围:810 MHz to 960 MHz 初级线圈阻抗: 次级线圈阻抗: 绝缘电压:23 dB 工作温度范围:- 40 C to + 85 C 端接类型:SMD/SMT 尺寸:6 mm L x 4.9 mm W x 1.6 mm H 产品:Splitters and Combiners |
| LT60030-1 | 制造商:LITTELFUSE 制造商全称:Littelfuse 功能描述:Class T Fuse Blocks - 300 and 600 Volt |
发布紧急采购，3分钟左右您将得到回复。