- 您现在的位置：买卖IC网 > PDF目录6104 > LT6106HS5#TRMPBF (Linear Technology)IC AMP CURRENT SENSE TSOT23-5 PDF资料下载
参数资料
| 型号： | LT6106HS5#TRMPBF |
| 厂商： | Linear Technology |
| 文件页数： | 11/12页 |
| 文件大小： | 0K |
| 描述： | IC AMP CURRENT SENSE TSOT23-5 |
| 标准包装： | 1 |
| 放大器类型： | 电流检测 |
| 电路数： | 1 |
| -3db带宽： | 200kHz |
| 电流 - 输入偏压： | 40nA |
| 电压 - 输入偏移： | 150µV |
| 电流 - 电源： | 70µA |
| 电流 - 输出 / 通道： | 1mA |
| 电压 - 电源，单路/双路(±)： | 2.7 V ~ 36 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-5 细型，TSOT-23-5 |
| 供应商设备封装： | TSOT-23-5 |
| 包装： | 标准包装 |
| 产品目录页面： | 1320 (CN2011-ZH PDF) |
| 其它名称： | LT6106HS5#TRMPBFDKR |
LT6106
8
6106fa
APPLICATIONS INFORMATION
magnitude. A sense resistor with integrated Kelvin sense
terminals will give the best results. Figure 2 illustrates the
recommended method.
This approach can be helpful in cases where occasional
bursts of high currents can be ignored.
Care should be taken when designing the board layout for
RIN, especially for small RIN values. All trace and inter-
connect resistances will increase the effective RIN value,
causing a gain error.
Selection of External Output Resistor, ROUT
The output resistor, ROUT, determines how the output cur-
rent is converted to voltage. VOUT is simply IOUT ROUT.
In choosing an output resistor, the maximum output volt-
age must rst be considered. If the following circuit is a
buffer or ADC with limited input range, then ROUT must be
chosen so that IOUT(MAX) ROUT is less than the allowed
maximum input range of this circuit.
In addition, the output impedance is determined by ROUT. If
the circuit to be driven has high enough input impedance,
then almost any useful output impedance will be accept-
able. However, if the driven circuit has relatively low input
impedance, or draws spikes of current such as an ADC
might do, then a lower ROUT value may be required in order
to preserve the accuracy of the output. As an example, if
the input impedance of the driven circuit is 100 times ROUT,
then the accuracy of VOUT will be reduced by 1% since:
VI
RR
OUT
IN DRIVEN
OUT
IN DRIVEN
=
+
=
()
IIR
IR
OUT
.
100
101
099
=
Error Sources
The current sense system uses an amplier and resistors
to apply gain and level shift the result. The output is then
dependent on the characteristics of the amplier, such as
gain and input offset, as well as resistor matching.
Ideally, the circuit output is:
VV
R
VR
I
OUT
SENSE
OUT
IN
SENSE
==
;
In this case, the only error is due to resistor mismatch,
which provides an error in gain only. However, offset volt-
age and bias current cause additional errors.
Figure 3. Shunt Diode Limits Maximum Input Voltage to Allow
Better Low Input Resolution Without Overranging
Figure 2. Kelvin Input Connection Preserves Accuracy with
Large Load Currents
Selection of External Input Resistor, RIN
RIN should be chosen to allow the required resolution
while limiting the output current to 1mA. In addition, the
maximum value for RIN is 500Ω. By setting RIN such that
the largest expected sense voltage gives IOUT = 1mA, then
the maximum output dynamic range is available. Output
dynamic range is limited by both the maximum allowed
output current and the maximum allowed output voltage,
as well as the minimum practical output signal. If less
dynamic range is required, then RIN can be increased
accordingly, reducing the maximum output current and
power dissipation. If low sense currents must be resolved
accurately in a system that has a very wide dynamic range,
a smaller RIN than the maximum current spec allows may
be used if the maximum current is limited in another way,
such as with a Schottky diode across RSENSE (Figure 3).
This will reduce the high current measurement accuracy
by limiting the result, while increasing the low current
measurement resolution.
LT6106
ROUT
VOUT
6106 F02
RIN
V+
LOAD
RSENSE
–
+
V+
V–
OUT
–IN
+IN
V+
LOAD
DSENSE
6106 F03
RSENSE
相关PDF资料 |
PDF描述 |
|---|---|
| P6SMB12AT3G | TVS ZENER UNIDIR 600W 12V SMB |
| SFM210-LPSE-D25-ST-BK | CONN HDR FMAL 50PS 1MM DL AU T/H |
| TSW-114-08-T-S | CONN HEADER 14POS .100" SNGL TIN |
| AD8542ARZ | IC OPAMP GP R-R CMOS 1MHZ 8SOIC |
| TSW-103-07-T-D | CONN HEADER 6POS .100" DUAL TIN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT6107 | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Temperature High Side Current Sense Amp in SOT-23 |
| LT6107MPS5#PBF | 制造商:Linear Technology 功能描述:SP Amp Current Sense Amp Single 36V 5-Pin TSOT-23 制造商:Linear Technology 功能描述:Bulk 制造商:Linear Technology 功能描述:AMPLIFIER, CURRENT SENSE, 200KHZ, TSOT-23-5; No. of Amplifiers:1; Input Bias Current:40nA; Input Offset Voltage:150V; Amplifier Case Style:TSOT-23; No. of Pins:5; Bandwidth:200kHz; Supply Voltage Min:2.7V; Supply Voltage Max:36V ;RoHS Compliant: Yes |
| LT6107MPS5#TRMPBF | 功能描述:IC AMP CURRENT SENSE HS TSOT23-5 RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 产品培训模块:Differential Circuit Design Techniques for Communication Applications 标准包装:1 系列:- 放大器类型:RF/IF 差分 电路数:1 输出类型:差分 转换速率:9800 V/µs 增益带宽积:- -3db带宽:2.9GHz 电流 - 输入偏压:3µA 电压 - 输入偏移:- 电流 - 电源:40mA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-VQFN 裸露焊盘，CSP 供应商设备封装:16-LFCSP-VQ 包装:剪切带 (CT) 产品目录页面:551 (CN2011-ZH PDF) 其它名称:ADL5561ACPZ-R7CT |
| LT6107MPS5#TRPBF | 功能描述:IC AMP CURRENT SENSE HS TSOT23-5 RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 其它有关文件:Automotive Product Guide 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 放大器类型:通用 电路数:1 输出类型:满摆幅 转换速率:3 V/µs 增益带宽积:10MHz -3db带宽:- 电流 - 输入偏压:1pA 电压 - 输入偏移:70µV 电流 - 电源:2.5mA 电流 - 输出 / 通道:48mA 电压 - 电源，单路/双路(±):2.7 V ~ 5.5 V，±1.35 V ~ 2.75 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:Digi-Reel® 其它名称:MAX4475AUT#TG16DKR |
| LT6107MPS5-TR | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Temperature High Side Current Sense Amp in SOT-23 |
发布紧急采购，3分钟左右您将得到回复。